Gear and Power Transmission Research Laboratory: Publications
Publications
- Hong, I., Aneshansley, E., Talbot, D., “Mechanical Power Loss of Spur Gears Subject to Various Surface Finish Pairings,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, Rosemont, IL, October 17-19 2022.
- Olson, R., Talbot, D., Michaud, M., Keller, J., Amendola, J., “Results of ISO/TS 6336-22 Evaluating Full Contact Zone,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, Rosemont, IL, October 17-19 2022.
- Celikay,A., Donmez, A., Kahraman, A., “An Experimental Study of Parametric Resonances of a Spur Gear Pair at Speeds Above its Primary Resonance,” Int. VDI Conference on Gears, Int. VDI Conference on Gears, Munich, Germany, September 12 – 14, 2022.
- Ryali, L., Talbot, D., “Dynamic Load Distribution of Planetary Gear Sets Subject to Both Internal and External Excitations,” Int. VDI Conference on Gears, Int. VDI Conference on Gears, Munich, Germany, September 12 – 14, 2022.
- Hong, I., Teaford, Z., Kahraman, A., “A Comparison of Gear Tooth Bending Fatigue Lives from Single Tooth Bending and Rotating Gear Tests,” Int. VDI Conference on Gears, Int. VDI Conference on Gears, Munich, Germany, September 12 – 14, 2022.
- Donmez, A., Kahraman, A., “A Generalized Torsional Dynamics Formulation for Multi-Mesh Gear Trains with Clearances and Torque Fluctuations,” ASME IDETC/CIE2022, ASME IDETC/CIE2022, St. Louis, MO, August 14-17 2022.
- Ryali, L., Talbot, D., “A Gear Load Distribution Model for a Planetary Gear Set with a Flexible Carrier,” International VDI Conference on Gears, International VDI Conference on Gears, Munich, Germany, September 18-20 2019.
- Blettery, H., Talbot, D., Kahraman, A., Xu, H., “A Methodology for Measurement of Loaded Transmission Error of a Hypoid Gear Pair with Misalignments,” International VDI Conference on Gears, International VDI Conference on Gears, Munich, Germany, September 18-20 2019.
- Vedera, K., Hong, I., Talbot, D., Kahraman, A., Zhou, S., “Power Loss Measurements of Rolling Element Bearings Subject to Combined Radial and Axial Loads,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Anaheim, CA, August 18-21 2019.
- Hu, Y., Talbot, D., Kahraman, A., “A Load Distribution Model for Double-Planet Planetary Gear Sets,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Anaheim, CA, August 18-21 2019.
- Anandika, M. N., Kahraman, A., Talbot, D., “An Experimental Investigation of the Impact of Random Spacing Errors on the Dynamic Transmission Error of Spur Gear Pairs,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Anaheim, CA, August 18-21 2019.
- Benatar, M., Handschuh, M., Kahraman, A., Talbot, D., “A Methodology to Experimentally Investigate the Impact of Wobble Errors on Contact Pattern and Static Transmission Error of Helical Gear Pairs,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Anaheim, CA, August 18-21 2019.
- Park, K., Kang, M., Lee, J., Son, W.C., Harianto, J., Kahraman, A., “Development of an Analysis Program to Predict Efficiency of Automotive Power Transmission and Its Applications,” SAE Technical Paper 2018-01-0398, SAE Technical Paper 2018-01-0398, Detroit, MI, April 10-12 2018.
- Case, S., Talbot, D., “Frequency Spectra of Static Transmission Error in Spur Gear due to Errors,” International Gear Conference, International Gear Conference, Lyon, France, August 26-28 2018.
- Hu, Y., Ryali, L, Talbot, D., Kahraman, A., “A Theoretical Study of the Overall Transmission Error of Planetary Gear Sets,” International Gear Conference, International Gear Conference, Lyon, France, August 26-28 2018.
- Talbot, D. Kahraman, A., “Simulation of Gear Wear using a Dynamic Load Distribution Model,” International VDI Conference on Gears, International VDI Conference on Gears, Munich, Germany, September 13-15 2017.
- Ligata, H., Kahraman, A., “Effects of External Splines on Deformations of Ring Gears of Planetary Gear Sets,” International VDI Conference on Gears, International VDI Conference on Gears, Munich, Germany, September 13-15 2017.
- Polly, J. Talbot, T, Kahraman, A. Singh, A., “An Experimental Investigation of Churning Power Losses of a Gearbox,” ASME Int. PTG Conference, ASME Int. PTG Conference, Cleveland, August 6-9 2017.
- Hu, Y., Talbot, D., Kahraman A., “A Load Distribution Model for Planetary Gear Sets,” ASME Int. PTG Conference, ASME Int. PTG Conference, Cleveland, August 6-9 2017.
- Anichowski, B., Talbot, D., Kahraman, A., “Dynamic Transmission Error Measurements from Spur Gear Pairs Having Tooth Indexing Errors,” ASME Int. PTG Conference, ASME Int. PTG Conference, Cleveland, August 6-9 2017.
- Moss, J., Kahraman, A., Wink, C., “An Experimental Study of Influences of Lubrication Methods on Efficiency and Contact Fatigue Life of Spur Gears,” ASME Int. PTG Conference, ASME Int. PTG Conference, Cleveland, August 6-9 2017.
- Janakiraman, V., Kahraman, A., Talbot, D., “Modeling of Steady-State Power Loss in Planetary Gear Trains of Automatic Transmissions,” Motion and Power Transmission Conference, Motion and Power Transmission Conference, Kyoto, Japan, February 2017.
- Benatar, M., Talbot, D., Kahraman, A., “An Experimental Investigation of Load Distribution of Spline Joint under Gear Mesh Loading,” Motion and Power Transmission Conference, Motion and Power Transmission Conference, Kyoto, Japan, February 2017.
- Ligata, H., Kahraman, A., “Effects of Rim Thickness and External Splines on Deformations of Ring Gear of Planetary Gear Sets,” International Conference on Power Transmissions, International Conference on Power Transmissions, Chongqing, China, October 2016.
- Hong, J., Talbot, D., Kahraman, A., “A Load Distribution Model of Major Diameter-Fit Spline Joints,” VDI International Gear Conference, VDI International Gear Conference, Munich, Germany, October 2015.
- Talbot, D., Kahraman, A., “A Dynamic Gear Load Distribution Model,” VDI International Gear Conference, VDI International Gear Conference, Munich, Germany, October 2015.
- Case, S., Talbot, D., “Frequency Spectra of Static Transmission Error in Spur Gear due to Errors,” International Gear Conference, International Gear Conference, Lyon, France, August 26-28 2018.
- Hu, Y., Ryali, L, Talbot, D., Kahraman, A., “A Theoretical Study of the Overall Transmission Error of Planetary Gear Sets,” International Gear Conference, International Gear Conference, Lyon, France, August 26-28 2018.
- Talbot, D. Kahraman, A., “Simulation of Gear Wear using a Dynamic Load Distribution Model,” Int. VDI Conference on Gears, Int. VDI Conference on Gears, Munich, Germany, Sept. 13-15 2017.
- Ligata, H., Kahraman, A., “Effects of External Splines on Deformations of Ring Gears of Planetary Gear Sets,” Int. VDI Conference on Gears, Int. VDI Conference on Gears, Munich, Germany, Sept. 13-15 2017.
- Polly, J. Talbot, T, Kahraman, A. Singh, A., “An Experimental Investigation of Churning Power Losses of a Gearbox,” ASME Int. PTG Conference, ASME Int. PTG Conference, Cleveland, Aug. 6-9 2017.
- Hu, Y., Talbot, D., Kahraman A., “A Load Distribution Model for Planetary Gear Sets,” ASME Int. PTG Conference, ASME Int. PTG Conference, Cleveland, Aug. 6-9 2017.
- Anichowski, B., Talbot, D., Kahraman, A., “Dynamic Transmission Error Measurements from Spur Gear Pairs Having Tooth Indexing Errors,” ASME Int. PTG Conference, ASME Int. PTG Conference, Cleveland, Aug. 6-9 2017.
- Moss, J., Kahraman, A., Wink, C., “An Experimental Study of Influences of Lubrication Methods on Efficiency and Contact Fatigue Life of Spur Gears,” ASME Int. PTG Conference, ASME Int. PTG Conference, Cleveland, Aug. 6-9 2017.
- Janakiraman, V., Kahraman, A., Talbot, D., “Modeling of Steady-State Power Loss in Planetary Gear Trains of Automatic Transmissions,” Motion and Power Transmission Conference, Motion and Power Transmission Conference, Kyoto, Japan, February 2017.
- Benatar, M., Talbot, D., Kahraman, A., “An Experimental Investigation of Load Distribution of Spline Joint under Gear Mesh Loading,” Motion and Power Transmission Conference, Motion and Power Transmission Conference, Kyoto, Japan, February 2017.
- Kwon, H.S., Kahraman, A., “Influence of Design Parameters on Mechanical Power Losses of Planetary Gear Sets,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Boston, MA, 2015.
- Leque, N., Kahraman, A., “A Three-dimensional Load sharing Model of Planetary Gear Sets Having Manufacturing Errors,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Boston, MA, 2015.
- Erkilic, E., Talbot, D., Kahraman, A., “A Model to Predict Pocketing Power Losses of Spiral Bevel Gears,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Boston, MA, 2015.
- Hong, J., Talbot, D., Kahraman, A., “A Stiffness Formulation for Spline Joints,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Boston, MA, 2015.
- Boguski, B., Kahraman, A., “An Experimental Study of the Motion Transmission Error of Planetary Gear Sets,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Boston, MA, 2015.
- Kwon, H.S., Kahraman, A., “Influence of Design Parameters on Mechanical Power Losses of Planetary Gear Sets,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Boston, MA, 2015.
- Talbot, D., Kahraman A., “A Methodology to Predict Power Losses of Planetary Gear Sets,” International Gear Conference, International Gear Conference, Lyon, France, August 26-28 2013.
- Talbot, D., Stilwell, A., Kahraman, A., Singh, A., Napau, I., “Mechanical Power Losses of Full-Complement Needle Bearings of Planetary Gear Sets: Model and Experiments,” International Gear Conference, International Gear Conference, Lyon, France, August 26-28 2013.
- Austin, J., Talbot D., Houser, D., Vijayakar, S., “Finite Element Evaluation of a Bearing Instrumentation Method for Evaluating Bearing Load Distributions and Roller Stresses of the Final Drive of a Wind Turbine Gearbox,” International Gear Conference, International Gear Conference, Lyon, France, August 26-28 2013.
- Hong, J., Talbot, D., Kahraman, A., “A Semi-analytical Load Distribution Model for Involute Splines,” International Gear Conference, International Gear Conference, Lyon, France, August 26-28 2013.
- Inalpolat, M., Handschuh, M., Kahraman, A., “Impact of Indexing Errors on Spur Gear Dynamics,” International Gear Conference, International Gear Conference, Lyon, France, August 26-28 2013.
- Hotait, M. A., Kahraman, A., “Investigation on the Effect of Dynamic Behavior on the Bending Fatigue Lives of Spur Gears,” International Gear Conference, International Gear Conference, Lyon, France, August 26-28 2013.
- Talbot, D., Kahraman, A., “An Efficiency Model for Planetary Gear Sets,” International Gear Conference, International Gear Conference, Lyon, France, August 26-28 2013.
- Kahraman, A., Hilty, D., Singh A., “An Experimental Investigation of Spin Power Losses of Planetary Gear Sets,” International Gear Conference, International Gear Conference, Lyon, France, August 26-28 2013.
- Kahraman, A., “Tribo-dynamic Behavior of Gear System,” International Gear Conference, International Gear Conference, Lyon, France, August 26-28 2013.
- Kahraman, A., “Modelling of Power Losses of Automotive Power Transmission Systems,” SAE 2013 Fuels, Lubricants, and aftertreatment symposium, SAE 2013 Fuels, Lubricants, and aftertreatment symposium, Long Beach, CA, November 19-21 2013.
- Hong, J., Talbot, D., and Kahraman, A., “A Deformable-Body Spline Joint Load Distribution Model,” VDI International Conference on Gears, VDI International Conference on Gears, Munich, Germany, October 7-9 2013.
- Li, S. and Kahraman, A., “A Micro-Pitting Model for Lubricated Point Contacts,” VDI International Conference on Gears, VDI International Conference on Gears, Munich, Germany, October 7-9 2013.
- LaBerge, K., Dykas, B., Shon, S., Kahraman, A., “Effect of Super-finishing on Spur Gear Efficiency: Experiment and Simulation,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Portland, OR, August 5-7 2013.
- Hotait, M. A. and Kahraman, A., “Estimation of Bending Fatigue Life of Hypoid Gears Using a Multiaxial Fatigue Criterion,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Portland, OR, August 5-7 2013.
- Talbot, D., Kahraman, A. and Seetharaman, S., “A Pocketing Power Loss Model for Helical Gears,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Portland, OR, August 5-7 2013.
- Artoni, A., Guiggiani, M., Kahraman, A., and Harianto, J., “Robust Optimization of Helical Gear Surface Modifications within Ranges of Torque and Misalignments,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Portland, OR, August 5-7 2013.
- Xu, H. Singh, A., Kahraman, A., Hurley, J., and Shon, S., “Effects of Bearing Prelaod, Oil Volume and Operating Temperature on Axle Power Losses,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Washington D.C., August 28-31 2011.
- Talbot, D., Kahraman, A. and Singh, A., “An Experimental Investigation of the Efficiency of Planetary Gear Sets,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Washington D.C., August 28-31 2011.
- Sanders, A., Houser, D.R., Kahraman, A., Harianto, J., and Shon, S., “An Experimental Investigation of the Effect of Tooth Asymmetry and Tooth Root Shape on Root Stresses and Single Tooth Bending Fatigue Life of Gear Teeth,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Washington D.C., August 28-31 2011.
- Kashyap, S., Houser, D.R., Smith, Z., Selvaraj, S., Casella, J., and Bradway, J., “Methods of Describing Plastic Gear Geometry After a Temperature Change with Application to the Prediction of Gear Load Distribution,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Washington D.C., August 28-31 2011.
- Boguski, B., Kahraman, A. and Nishino, T., “A New Method to Measure Planet Load Sharing and Sun Gear Radial Orbits of Planetary Gear Sets,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Washington D.C., August 28-31 2011.
- Artoni, A., Gabiccini, M., Guigguani, M., and Kahraman, A., “Multi-objective Ease-off Optimization of Hypoid Gears for their Efficiency, Noise and Durability Performances,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Washington D.C., August 28-31 2011.
- Xu, H. , Singh, A., Maddock, D., Kahraman, A., and Hurley, J., “Thermal Mapping of an Automotive Rear Axle,” SAE Noise and Vibration Conference, SAE Noise and Vibration Conference, Detroit, MI, April 12-14 2011.
- Marambedu K.R., Houser, D.R., and Ligata, H., “Microgeometry Modifications for Load Distribution Improvement and Transmission Error Reduction of Loaded Straight Bevel Gears,” VDI International Conference on Gears, VDI International Conference on Gears, Munich, Germany, October 4-6 2010.
- Hotait M., Kahraman, A. and Nishino, T., “An Investigation of Influence of Misalignments on Root Stresses of Hypoid Gears,” VDI International Conference on Gears, VDI International Conference on Gears, Munich, Germany, October 4-6 2010.
- Hotait, M., Talbot, D., and Kahraman, A., “An Investigation of the Influence of Shaft Misalignments on Bending Stresses of Helical Gears with Lead Crown,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Las Vegas, NV, September 2010.
- Li, S., Vaidyanathan, A., Harianto, J., and Kahraman, A., “Influence of Design Parameters and Micro-Geometry on Mechanical Power Losses of Helical Gear Pairs,” JSME International Conference - Motion and Power Transmission, JSME International Conference - Motion and Power Transmission, Sendai, Japan, May 13-15 2009.
- Singh, A., Kahraman, A., and Ligata, H., “Internal Gear Strains and Load Sharing in Planetary Transmissions – Model and Experiments,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Las Vegas, NV, September 2009.
- Ligata, H., Kahraman, A, and Singh. A., “Influence of Gear Rim Deflections on Planetary Gear Set Behavior,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, San Diego, CA, September 2009.
- Kolivand, M. and Kahraman, A., “An Ease-Off Based Method for Loaded Tooth Contact Analysis of Hypoid Gears having Local and Global Surface Deviations,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, San Diego, CA, September 2009.
- Houser, D.R., “The Effect of Manufacturing Microgeometry Variations on the Load Distribution Factor and on Gear Contact and Root Stresses,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, San Antonio, TX, October 12-14 2008.
- Bednarek, G., Kahraman, A., and Seetharaman, S., “Development of an Efficiency Model for Manual Transmissions,” VDI International Conference on Gears, VDI International Conference on Gears, Freidrichhafen, Germany, June 17-19 2008.
- Kahraman, A., Seetharaman, S., Szweda, T., Kirchner, E., Olsson, M., and Bednarek, G., “Development of an Efficiency Model for Transmissions,” CTI Conference, CTI Conference, Berlin, Germany, December 2008.
- Ligata, H., Kahraman, A., and Singh, A., “Influenza Degli Errori di Lavorazione Sui Carichi Nei Rotismi Epicicloidali,” Organi di Transmissione, Organi di Transmissione, November 2008.
- Petry-Johnson, T., Kahraman, A., Anderson N.E., and Chase, D., “Experimental Investigation of Spur Gear Efficiency,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Las Vegas, NV, September 2008.
- Rosander, P., Bednarek, G., Seethharaman, S., and Kahraman, A., “Entwicklung eines Wirkungsgrad-Modells fur Sahalltgetriebe,” Automobiltechnische Zeitschrift (ATZ), Automobiltechnische Zeitschrift (ATZ), April 2008.
- Kahraman, A., Lim, J., and Ding, H., “A Dynamic Model of a Spur Gear Pair with Friction,” 12th IFToMM World Congress, 12th IFToMM World Congress, Besancon, France, June 18-21 2007.
- Inalpolat, M. and Kahraman, A., “Free Vibration Analysis of Multi-Stage Planetary Gear Trains,” Inter-Noise, Inter-Noise, Istanbul, Turkey, August 28-31 2007.
- Ligata. H., Kahraman, A., and Singh, A., “An Experimental Investigation of the Influence of Manufactruing Errors on the Planetary Gear Stresses and Load Sharing,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Las Vegas, NV, September 2007.
- Harianto, J. and Houser, D.R., “A Methodology for Obtaining Optimum Gear Tooth Micro-Topographies for Noise and Stress Minimization Over a Broad Operating Torque Range,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Las Vegas, NV, September 2007.
- Houser, D.R., Shon, S., and Harianto, J., “An Evaluation of FZG Micropitting Test Procedures and Results for the Crowned AGMA Test Gears,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, Orlando, FL, 2006.
- Anderson, N., Petry-Johnson, T., Chase, D., and Kahraman, A., “Effect of Surface Characteristics and Lubricants on Spur Gear Efficiency,” FISITA 2006 World Automotive Congress, FISITA 2006 World Automotive Congress, Yokohama, Japan, October 22-27 2006.
- Espin, S., Perret-Liaudet, J. and Kahraman, A., “Etude Theoreque et Expermentale de la Resonance non Lineaire d’un Engrenage Droit Induite par le Jeu Entre Dents,” XV Collogue Vibrations Chocs et Bruit, XV Collogue Vibrations Chocs et Bruit, Ecully, France, June 2006.
- Houser, D. R. and Harianto, J., “The Effect of Micro-Geometry and Load on Helical Gear Noise Excitations,” SAE Noise and Vibration Conference, SAE Noise and Vibration Conference, Traverse City, MI, 2005.
- Xu, H.and Kahraman, A., “Prediction of Friction Power Losses of Hypoid Gear Pairs,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, Chicago, IL, 2005.
- Xu, H., Kahraman, A., and Houser, D.R., “A Model to Predict Friction Losses of Hypoid Gears,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, 2005.
- Ding, H. and Kahraman, A., “Interactions between Gear Dynamic and Gear Wear,” 17th AIMeTA Congress of Theoretical and Applied Mechanics, 17th AIMeTA Congress of Theoretical and Applied Mechanics, Florence, Italy, September 11-15 2005.
- Xu, H. and Kahraman, A., “A Frictional Efficiency Loss Model for Helical Gears,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Long Beach, CA, September 2005.
- Tamminnana, V. K., Kahraman A., and Vijayakar, S., “On the Relationship Between the Dynamic Factors and Dynamic Transmission Error of Spur Gear Pairs,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Long Beach, CA, September 2005.
- Harianto, J., and Houser, D.R., “The Effect of Profile Relied on the Noise Excitation of Helical Gear,” Gear Solutions Magazine, Gear Solutions Magazine, March 2005.
- Bajpai, P., Kahraman, A., and Anderson, N.E., “Optimization of Gear Tooth Profiles for Minimized Wear,” STLE Annual Meeting, STLE Annual Meeting, Toronto, Canada, May 2004.
- Uematsu, S., Lyu, S.K., Houser, D.R., Lim, J.S., and Lu, L., “A Study on Reducing the Gear Tooth Profile Error by Finish Roll Forming,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Chicago, IL, September 2-6 2003.
- Kartik, V., and Houser, D.R., “Analytical Predictions for the Transmission Error Excitation in Various Multiple-Mesh Gear-Trains,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Chicago, IL, September 2-6 2003.
- Eritenel, T., Houser, D.R., Vijayakar, S.M., and Casella, J.M., “Effect of Tooth Deflection and Corner Contact on Backside Separation (Backlash) of Gear Pairs,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Chicago, IL, September 2-6 2003.
- Chang, S., Houser, D.R., and Harianto, J., “Tooth Flank Corrections of Wide Face Width Helical Gears That Account for Shaft Deflections,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Chicago, IL, September 2-6 2003.
- Binney, D. A., Vinayak H., Gmirya Y., Zunski, L.M., Houser, D.R., and Ames, E.C., “Face Gear Transmission Development Program at Sikorsky Aircraft,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Chicago, IL, September 2-6 2003.
- Kubur, M., Kahraman, A., Zini, D., and Kienzle, K., “Dynamic Analysis of a Multi-Shaft Helical Gear Transmission by Finite Elements,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Chicago, IL, September 2-6 2003.
- Kahraman, A., Kienzle, K., and Zini, D., “A Generalized Formulation for Kinematic and Powerflow analysis of Automatic Transmission Planetary Gear Trains,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Chicago, IL, September 2-6 2003.
- Bajpai, P., Kahraman, A., and Anderson, N. E., “A Surface Wear Model for Parallel Axis Gear Pairs,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Chicago, IL, September 2-6 2003.
- Moraru, L., Keith, T.G., and Kahraman, A., “Aspect Regarding the Load Carrying Mechanisms in Lubricated, Rough Line Contacts,” STLE Annual Meeting, STLE Annual Meeting, New York, NY, April 2003.
- Cioc, C., Cioc, S., Keith, T.G., and Kahraman, A., “A Deterministic Mixed Elastohydrodynamic Lubrication Model of High-Speed Rotorcraft Components,” STLE Annual Meeting, STLE Annual Meeting, New York, NY, April 2003.
- Ueda, Y., and Houser, D.R., “Optimum Design and Manufacturing Robustness for Gear Whine of Helical Gear,” VDI International Conference on Gears, VDI International Conference on Gears, 2002.
- Houser, D.R., Sorenson, J., Harianto, J., Wijaya, H., and Satyanarayanan, M., “Comparison of Analytical Predictions with Dynamic Noise and Vibration Measurements for a Simple Idler Gearbox,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, 2002.
- Houser, D.R. and Harianto, J., “A Gear Design Optimization Procedure that Identifies Robust, Minimum Stress and Minimum Noise Gear Pair Designs,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, St. Louis, MO, October 20-22 2002.
- Kahraman, A. and Wagaj, P., “Reduction Vibration Levels of Gear Systems via Optimization of Tooth profile Modifications,” 6th Biennial ASME Conference on Engineering Systems Design and Analysis, 6th Biennial ASME Conference on Engineering Systems Design and Analysis, Istanbul, Turkey, July 8-11 2002.
- Kartik, V., Houser, D.R., and Sorenson, J. D., “Gear Noise Responses from a Variety of Applications - Modeling and Experimentation,” Inter-Noise, Inter-Noise, Dearborn, MI, August 2002.
- Kahraman, A., “An Analytical and Experimental Study of Nonlinear Spur Gear Dynamics,” SFA Congress, SFA Congress, Paris, France, June 2002.
- Cioc, C., Keith, T.G., and Kahraman, A., “A Deterministic Elastohydrodynamic Lubrication Model for High-Speed Transmission Components,” STLE Annual Meeting, STLE Annual Meeting, Houston, TX, May 2002.
- Kahraman, A., Umrani, M., “A Deformable-Body Dynamic Analysis of Planetary Gears with Thin Rims,” The India-USA Symposium on Emerging Trends in Vibration and Noise Engineering, The India-USA Symposium on Emerging Trends in Vibration and Noise Engineering, Columbus, OH, December 2001.
- Colabawala, M., Sorenson, J. D., and Houser, D.R., “An Experimental Procedure for Characterization of Gear Whine Noise in a Variety of Vehicle Applications,” SAE Noise and Vibration Conference, SAE Noise and Vibration Conference, Traverse City, MI, 2001.
- Houser, D.R., Vaishya, M., and Sorenson, J., “An Experimental Investigation into Vibro-Acoustic Effects of Friction in Gear Meshes,” SAE Noise and Vibration Conference, SAE Noise and Vibration Conference, 2001.
- Houser, D.R. and Harianto, J., “Manufacturing Robustness Analysis of the Noise Excitation and Design of Alternative Gear Sets,” SAE Noise and Vibration Conference, SAE Noise and Vibration Conference, 2001.
- Houser, D.R. and Harianto, J., “Design Robustness and Its Effect on Transmission Error and Other Design Parameters,” International Conference on Mechanical Transmissions, International Conference on Mechanical Transmissions, China, 2001.
- Wijaya, H., Houser, D. R., and Harianto, J., “The Effect of Spacing Errors and Runout on Transverse Load Sharing and the Dynamic Factor of Spur and Helical Gears,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, Detroit, MI, October 3-5 2001.
- Kahraman, A. and Umrani, M., “An Investigation of Planetary Gear Dynamic Stress Factors as a Function of Gear Rim Thickness,” The India-USA Symposium on Emerging Trends in Vibration and Noise Engineering, The India-USA Symposium on Emerging Trends in Vibration and Noise Engineering, Columbus, OH, December 2001.
- Houser, D. R., Sorenson, J., and Harianto, J., “Development of a Data Base for Transmission Noise Evaluation,” The India-USA Symposium on Emerging Trends in Vibration and Noise Engineering, The India-USA Symposium on Emerging Trends in Vibration and Noise Engineering, Columbus, OH, December 2001.
- Houser, D.R., Harianto, J., and Ueda, Y., “The Effect of Manufacturing Errors on Gear Design Metrics Using a Robustness Scheme,” JSME International Conference - Motion and Power Transmission, JSME International Conference - Motion and Power Transmission, Fukuoka, Japan, November 2001.
- Bodas, A. and Kahraman, A., “Influence of Carrier and Gear Manufacturing Errors on the Static Planet Load Sharing Behavior of Planetary Gear Sets,” International Motion and Power Transmission Conference, International Motion and Power Transmission Conference, Fukuoka, Japan, November 2001.
- Phansalkar, S., Kahraman, A. and Anderson, N., “A Comparative Study of EHL Behavior of Smooth and Asperity Contacts of Helical Gears and Rollers,” STLE Annual Meeting, STLE Annual Meeting, Orlando, FL, May 2001.
- Cioc, C., Moraru, L., Keith, T. and Kahraman, A., “An Integrated, Physics-Based Lubrication Analysis Methodology for Helicopter Transmission Gear Surfaces with Asperities,” Annual Meeting of the American Helicopter Society, Annual Meeting of the American Helicopter Society, Washington D.C., May 2001.
- Hochmann, D., and Houser, D.R., “Friction Forces as a Dynamic Excitation Source in Involute Spur and Helical Gearing,” International Gearing Conference, International Gearing Conference, 2000.
- Snow, C., Houser, D.R., and Luscher, A.F., “The Effect of Gating and Material on Measured Transmission Error and Noise of Injection Molded Gears,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Baltimore, MD, September 2000.
- Vaishya, M., and Houser, D.R., “Modeling and Analysis of Sliding Friction in Gear Dynamics,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Baltimore, MD, September 2000.
- Kahraman, A. and Vijayakar, S., “Effect of Internal Gear Flexibility on the Quasi-static Behavior of a Planetary Gear Set,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Baltimore, MD, September 2000.
- Houser, D. R., Harianto, J., Chandrasekaran, B., Josephson, J. R., and Iyer, N., “A Multi-Variable Approach to Determine the "Best" Gear Design,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Baltimore, MD, September 2000.
- Houser, D.R., and Su, X., “Definition and Inspection of Profile and Lead of a Worm Wheel,” World Congress-Gear and Power Transmission, World Congress-Gear and Power Transmission, 1999.
- Houser, D.R., Harianto, J., Sorenson, J. D., Lim, T. C., Myers, C. H., Gordon, B.E., and Berry, S., “Case History: Engine Timing Gear Noise Reduction,” SAE Noise and Vibration Conference, SAE Noise and Vibration Conference, Traverse City, MI, May 1999.
- Dunn, A.L., Houser, D.R., and Lim, T. C., “Methods for Researching Gear Whine in Automotive Transaxles,” SAE Noise and Vibration Conference, SAE Noise and Vibration Conference, Traverse City, MI, May 1999.
- Houser, D.R., Luscher, A.F., and Regalado, I., “The General Optimization of Cylindrical Gears Including Robustness,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Las Vegas, NV, September 1999.
- Houser, D.R., Luscher, A. F., and Regalado, I. C., “The Multi-Objective Optimization of Nonstandard Gears Including Robustness,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, Denver, CO, October 1999.
- Houser, D.R., Su, X., Vaishya, M., and Vijayakar, S.M., “Effects of Wear on the Meshing Contact of Worm Gearing,” AGMA Fall Techincal Meeting, AGMA Fall Techincal Meeting, Denver, CO, October 1999.
- Kahraman, A., “Static Load Sharing Characteristics of Transmission Planetary Gear Sets: Model and Experiment,” Transmission and Driveline Systems Symposium, SP-1440, Transmission and Driveline Systems Symposium, SP-1440, Detroit, MI, March 1999.
- Houser, D.R., “Gear Noise State of The Art,” InterNoise, InterNoise, 1998.
- Su, X., and Houser, D.R., “Programmable Separation of Runout From Profile and Lead Inspection Data for Gear Teeth With Arbitrary Modifications,” Gear Technology, Gear Technology, 1998.
- Houser, D.R., “Influence of Manufacturing Tolerances on Gear Transmission Error and Noise,” 3rd International Advanced Gear Manufacturing and Processing, 3rd International Advanced Gear Manufacturing and Processing, Dearborn, MI, May 1998.
- Houser, D.R., and Harianto, J., “A Method for Predicting the Dynamic Root Stresses of Helical Gear Teeth,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, 1998.
- Su, X., and Houser, D.R., “Calculation of Wobble From Lead Inspection Data of Gear Teeth With Modifications,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Atlanta, GA, September 13-16 1998.
- Singh, A., Houser, D.R., and Vijayakar, S., “Detecting Gear Tooth Breakage Using Acoustic Emission: A Feasibility and Sensor Placement Study,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Atlanta, GA, September 13-16 1998.
- Regalado, I., and Houser, D.R., “Profile Modifications for Minimum Static Transmission Error in Cylindrical Gears,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Atlanta, GA, September 13-16 1998.
- Kalluri, R., and Houser, D.R., “A Possible Strategy for Incorporating Edge Effects in Root Stress Estimation of Helical Gears,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Atlanta, GA, September 13-16 1998.
- Lim, T. C., and Houser, D.R., “Dynamic Analysis of Layshaft Gears in Automotive Transmission,” SAE Noise and Vibration Conference, SAE Noise and Vibration Conference, 1997.
- Houser, D.R., and Singh, R.S., “NVH Research Facilities at The Ohio State University: Existing Facilities and Envisioned Enhancements,” SAE Noise and Vibration Conference, SAE Noise and Vibration Conference, 1997.
- Su, X., and Houser, D.R., “Coordinate Measurement and Reverse Engineernig of ZK Type Worm Gearing,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, 1997.
- Liauwnardi, L., Luscher, A., and Houser, D.R., “Plastic Gear Transmission Error Measurements and Predictions,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, 1997.
- Liauwnardi, L., Houser, D.R., and Luscher, A., “Measurements and Predictions of Plastic Gear Transmission Errors with Comparisons to the Measured Noise of Plastic and Steel Gears,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, 1997.
- Dziech, A., and Houser, D.R., “Refinements in Root Stress Predictions for Edges of Helical Gear Teeth,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, 1997.
- Houser, D.R., and Schroeder, G., “Dynamic Characterization of a Planetary Test Rig Using Modal Analysis,” SEM 14th International Modal Analysis Conference, SEM 14th International Modal Analysis Conference, Dearborn, MI, 1996.
- Houser, D.R., Bolze, V.M., and Graber, J.M., “A Comparison of Predicted and Measured Dynamic and Static Transmission Error for Spur and Helical Gear Sets,” SEM 14th International Modal Analysis Conference, SEM 14th International Modal Analysis Conference, Dearborn, MI, 1996.
- Börner, J., and Houser, D.R., “Friction and Bending Moments as Gear Noise Excitations,” SAE Noise and Vibration Conference, SAE Noise and Vibration Conference, Indianapolis, IN, August 1996.
- Prabhu, M. S., and Houser, D.R., “A Hybrid Finite Element Approach for Analyzing the Load Distribution and Transmission Error in Thin-Rimmed Gears,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, 1996.
- Kahraman, A. and Blankenship, G.W., “Torsional Gear Pair Dynamics, Part-III: Effect of Involute Profile Modifications,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, San Diego, CA, 1996.
- Kahraman, A. and Blankenship, G.W., “Torsional Gear Pair Dynamics, Part-II: Effect of Involute Contact Ratio,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, San Diego, CA, 1996.
- Houser, D.R., Bolze, V.M., and Graber, J.M., “Static and Dynamic Transmission Error Measurements and Predictions for Spur and Helical Gear Sets,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, 1996.
- Blankenship, G. W. and Kahraman, A., “Torsional Gear Pair Dynamics, Part-I: Characterization of Forced Response,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, San Diego, CA, 1996.
- Börner, J., and Houser, D.R., “Dynamic Distribution of Load and Stress on External Involute Gearings,” AGMA Fall Techincal Meeting, AGMA Fall Techincal Meeting, 1996.
- Celik, M., Houser, D.R., and Bilir, O. G., “Application of Boundary Elements to Thin-Rimmed Geometry of Spur Gears,” 7th International Machine Design and Production Conference, 7th International Machine Design and Production Conference, Metu, Ankara, Turkey, September 1996.
- Narayan, A., Houser, D.R., and Vijayakar, S., “Study of Effect of Machining Parameters on Performance of Worm Gears,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, 1995.
- Harianto, J., and Houser, D.R., “The Effect of Manufacturing Errors on the Predicted Dynamic Factors of Spur Gears,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, 1995.
- Singh, A., and Houser, D.R., “Analysis of Off-Line of Action Contact at the Tips of Gear Teeth,” SAE Noise and Vibration Conference, SAE Noise and Vibration Conference, Milwaukee, WI, September 1994.
- Kahraman, A. and Blankenship, G.W., “Planet Mesh Phasing in Epicyclic Gear Sets,” International Gearing Conference, International Gearing Conference, Newcastle upon Tyne, 1994.
- Hochmann, D., and Houser, D.R., “An Experimental Test Stand for Measurements on Loaded Parallel Axis Gears,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, 1994.
- Blazakis, C. A., and Houser, D.R., “Finite Element and Experimental Analysis of the Effects of Thin-Rimmed Gear Geometry on Spur Gear Fillet Stresses,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, 1994.
- Houser, D. R., Oswald, F.B., Valco, M.J., Drago, R.J., and Lenski, J.W., “Comparison of Transmission Error Predictions With Noise Measurements for Several Spur and Helical Gears,” AIAA Joint Propulsion Conference, AIAA Joint Propulsion Conference, Indianapolis, IN, June 1994.
- Clapper, M. L., and Houser, D.R., “A Boundary Element Procedure for Predicting Helical Gear Root Stresses and Load Distribution Factors,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, 1994.
- Sundaresan, S., Ishii, K., and Houser, D.R., “A Robust Optimization Procedure With Variations on Design Variables and Constraints,” ASME Advances in Design Automation, ASME Advances in Design Automation, 1993.
- Singh, R., and Houser, D.R., “Engineering Science Research Issues in High Power Density Transmission Dynamics for Aerospace Applications,” AIAA Joint Propulsion Conference, AIAA Joint Propulsion Conference, 1993.
- Wheitner, J., Houser, D.R., and Blazakis, C.A., “Gear Tooth Bending Fatigue Crack Detection by Acoustic Emisions and Tooth Compliance Measurements,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, 1993.
- Vaidyanathan, S., Houser, D.R., and Busby, H.R., “A Rayleigh-Ritz Approach to Determine Compliance and Root Stresses in Spiral Bevel Gears Using Shell Theory,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, 1993.
- Clapper, M.L., and Houser, D.R., “Prediction of Fully Reversed Stresses at the Base of the Root in Spur and Double Helical Gears in a Split Torque Helicopter Transmission,” Rotary Wing Propulsion Specialists' Meeting, Rotary Wing Propulsion Specialists' Meeting, Williamsburg, VA, October 1993.
- Rao, R., Srinivasulu, B., “Studies on the Dynamic Performance of A Spur Gear With Hollow Teeth,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, 1992.
- Thomas, J., and Houser, D.R., “A Procedure for Predicting the Load Distribution and Transmission Error Characteristics of Double Helical Gears,” World Congress-Gear and Power Transmission, World Congress-Gear and Power Transmission, 1992.
- Rao, A., and Houser, D.R., “Studies on Helical Gear Blanks: Flexibility Effects on Surface Durability and Design Optimization,” USIF, USIF, 1992.
- Caliskan, M. and Kahraman, A., “Analytical Study of Noise Generated by Rotating Textile Spindles,” Inter-Noise, Inter-Noise, Toronto, Canada, 1992.
- Vinayak, H., and Houser, D.R., “A Comparison of Analytical Prediction With Experimental Measurements of Transmission Error of Misaligned Loaded Gears,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, 1992.
- Kahraman, A., “Dynamic Analysis of a Multi-Mesh Helical Gear Train,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Phoenix, AZ, 1992.
- Adjunta, J., and Houser, D.R., “A Study on the Shrinkage Characteristics and Dimensional Accuracy of Cast Gears,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, 1992.
- Sundaresan, S., Ishii, K., and Houser, D.R., “Design of Helical Gears With Minimum Transmission Error Under Manufacturing and Operating Variances,” JSME International Conference - Motion and Power Transmission, JSME International Conference - Motion and Power Transmission, 1991.
- Biggert, P., and Houser, D.R., “Gear Ghost Noise - A Case History Using Single Flank Transmission Error Measurements,” NOISE-CON, NOISE-CON, 1991.
- Yau, E., Busby, H.R., and Houser, D.R., “A Rayleigh-Ritz Approach for Modeling the Bending and Shear Deflections of Gear Teeth,” JSME International Conference - Motion and Power Transmission, JSME International Conference - Motion and Power Transmission, Hiroshima, Japan, November 1991.
- Kahraman, A., “Effect of Axial Vibrations on the Dynamics of a Helical Gear Pair,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Miami, FL, 1991.
- Vijayakar, S. M., and Houser, D.R., “Contact Analysis of Gears Using a Combined Finite Element and Surface Integral Method,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, 1991.
- Houser, D.R., “Research of the Ohio State University Gear Dynamics and Gear Noise Research laboratory,” International Machine and Engineering, International Machine and Engineering, Cambridge, England, April 1990.
- Kahraman, A. and Singh, R., “Linear and Nonlinear Dynamic Models of Geared Rotor-bearing Systems,” The Eighth International Modal Analysis Conference, The Eighth International Modal Analysis Conference, Florida, 1990.
- Kahraman, A. and Singh, R., “Routes to Chaos in a Geared System with Backlash,” The 120th Meeting of the Acoustical Society of America, The 120th Meeting of the Acoustical Society of America, San Diego, CA, 1990.
- Agrawal, R., Sarkar, B., Kinzel, G., and Houser, D.R., “Optimal Design of Straight Bevel Gears,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, October 1990.
- Sundaresan, S., Ishii, K., and Houser, D.R., “A Procedure that Accounts for Manufacturing Errors in the Design Minimization of Transmission Error in Helical Gears,” AGMA Fall Techincal Meeting, AGMA Fall Techincal Meeting, October 1990.
- Houser, D.R., and Blankenship, G.W., “Methods for Measuring Gear Transmission Error Under Load and at Operating Speeds,” SAE Noise and Vibration Conference, SAE Noise and Vibration Conference, Milwaukee, WI, September 1989.
- Stegemiller, M.E., and Houser, D.R., “A Three Dimensional Analysis of the Base Flexibility of Gear Teeth,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, 1989.
- Kahraman, A., Ozguven, H. N., Houser, D. R., and Zakrajsek, J. J., “Dynamic Analysis of Geared Rotors by Finite Elements,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Chicago, IL, 1989.
- Kahraman, A. and Singh, R., “Effect of Mean Load on the Nonlinear Behavior of a Spur Gear Noise Source,” Inter-Noise, Inter-Noise, Newport Beach, CA, December 1989.
- Vijayakar, S. M., Houser, D.R., and Busby, H.R., “A Summary of New Finite Element Techniques With Special Applications to Gears,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Zhengzhou, China, November 1988.
- Blankenship, G.W., Houser, D.R., and Carriere, D.L., “Development of a Variable Center Distance Gear Noise Test Facility,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, 1988.
- Vijayakar, S.M., Sarkar, B., and Houser, D.R., “Gear Tooth Profile Determination From Arbitrary Rack Geometry,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, October 1987.
- Ozguven, H.N., and Houser, D.R., “Gear Dynamic Models Used in Noise Analysis,” NOISE-CON, NOISE-CON, Penn State University, June 8-10 1987.
- Houser, D.R., Linzell, S., and Previte, T., “Factors Which Affect Shifting Rate of a Rubber Belt Continuously Variable Transmission,” World Congress-Gear and Power Transmission, World Congress-Gear and Power Transmission, 1986.
- Kahraman, A. and Caliskan M., “Sound Radiation from Textile Ring-spinning Spindles with Mass Unbalance,” The 12th International Conference on Acoustics, The 12th International Conference on Acoustics, Toronto, Canada, 1986.
- Kahraman, A. and Caliskan M., “Dynamics of Textile Spinning Spindles and Rotors,” International Rotordynamics Conference, International Rotordynamics Conference, Tokyo, Japan, 1986.
- Vijayakar, S. M., and Houser, D.R., “The Use of Boundary Elements for the Determination of the Geometry Factor,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, 1986.
- Houser, D.R., “Gear Noise Sources and Their Prediction Using Mathematical Models,” OEM Conference, OEM Conference, Philadelphia, September 1985.
- Pape, D.B., and Houser, D.R., “Signal Processing for the Detection of Gear Manufacturing Discrepancies,” NOISE-CON, NOISE-CON, Columbus, OH, June 1985.
- Yakubek, D., Busby, H.R., and Houser, D.R., “Three-Dimensional Deflection Analysis of Gear Teeth Using Both Finite Element Analysis and a Tapered Plate Approximation,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, 1985.
- Busby, H.R., and Houser, D.R., “Plate Bending and Finite Element Analysis of Spur and Helical Gear Tooth Deflection,” AGMA Fall Techincal Meeting, AGMA Fall Techincal Meeting, 1985.
- Zaremsky, G.J., Singh, R., and Houser, D.R., “Modal Analysis of a Gear Housing Plate Using Acoustic Intensity Measurements,” 2nd International Modal Analysis Conference, 2nd International Modal Analysis Conference, 1984.
- Tavakoli, M.S., and Houser, D.R., “Optimum Profile Modifications for the Minimization of Static Transmission Errors of Spur Gears,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, Cambridge, MA, October 7-10 1984.
- Houser, D.R., and Smigel, R., “Gear Load Distribution and Transmission Error Modeling,” AGMA Fall Technical Meeting, AGMA Fall Technical Meeting, Montreal, Canada, October 1983.
- Singh, R., Kinzel, G.L., and Houser, D.R., “Gear Noise Modeling,” Inter-Noise, Inter-Noise, Miami, FL, December 1980.
- Houser, D.R., “Basis for Spectral Analysis,” 5th National Council Canada Turbine Seminar, 5th National Council Canada Turbine Seminar, 1978.
- Drosjack, M.J., and Houser, D.R., “An Experimental and Theoretical Study of the Effects of Simulated Pitch Line Pitting on the Vibration of a Geared System,” ASME Power Transmission and Gearing Conference, ASME Power Transmission and Gearing Conference, 1977.
- Houser, D.R., Drosjack, M.J., and Hogg, G.W., “Vibration Diagnostics in Helicopter Power Trains,” AGARD Conference, AGARD Conference, 1974.
- Handschuh, M., Guner, A., Kahraman, A., “An Experimental Investigation of Windage and Oil Churning Power Losses of Gears and Discs,” Journal of Tribology, 237, 163-177, 2022.
- Donmez, A., Kahraman, A., “Characterization of Nonlinear Rattling Behavior of a Gear Pair Through a Validated Torsional Model,” Journal of Computational and Nonlinear Dynamics, 17, 041006, 2022.
- Donmez, A., Kahraman, A., “Influence of Various Manufacturing Errors on Gear Rattle,” Mechanism and Machine Theory, 173, 104868, 2022.
- Donmez, A., Kahraman, A., “Experimental and Theoretical Investigation of Vibro-impact Motions of a Gear Pair Subjected to Torque Fluctuations to Define a Rattle Noise Severity Index,” Journal of Vibration and Acoustics, 144, 041001, 2022.
- Dindar, A., Chaudhury, K., Kahraman, A., “Mechanical Power Losses of Ball Bearings: Model and Experimental Validation,” Journal of Tribology, 144, 051603, 2022.
- Celikay,A., Donmez, A., Kahraman, A., “An Experimental and Theoretical Study of Subharmonic Resonances of a Spur Gear Pair,” Journal of Sound and Vibration, 515, 11642, 2021.
- Ryali, L., Verma, A., Hong, I., Talbot, D., Zhu, F., “Experimental and Theoretical Investigation of Quasi-Static System Level Behavior of Planetary Gear Sets,” Journal of Mechanical Design, 143, 103401, 2021.
- Dindar, A., Hong, I., Garg, A., Kahraman, A., “A Methodology to Measure Power Losses of Rolling Element Bearings under Combined Radial and Axial Loading Conditions,” Tribology Transactions, 65(1), 137-152, 2021.
- Ryali, L., Talbot, D., “A Dynamic Load Distribution Model for a Planetary Gear Sets,” Mechanism and Machine Theory, 158, 104229, 2021.
- Li, S., Kahraman, A., “A Scuffing Model for Spur Gear Contacts,” Mechanism and Machine Theory, 156, 104161, 2021.
- Dindar, A., Chaudhury, K., Hong, I., Kahraman, A., Wink, C., “An Experimental Methodology to Determine Components of Power Losses of a Gearbox,” Journal of Tribology, Vol. 143, 2021.
- Kang, M. R. and Kahraman, A., “An Experimental and Theoretical Study of Quasi-Static Behavior of Double-Helical Gear Sets,” Journal of Mechanical Design, Vol. 143, 043401, 2021.
- Handschuh, M., Li, S., Kahraman, A., Talbot, D., “An Experimental and Theoretical Methodology to Develop Scuffing Limits for Relatively Smooth High-Speed Contacts,” Tribology Transactions, Vol. 63 No. 5, 781-795, 2020.
- Hong, I. J., Kahraman, A., Anderson, N., “An Experimental Evaluation of High-Cycle Gear Tooth Bending Fatigue Lives Under Fully Reversed and Fully Released Loading Conditions with Application to Planetary Gear Sets,” Journal of Mechanical Design, 143, 23402, 2020.
- Handschuh, M., Kahraman, A., Anderson, N., “Development of a High-Speed Two-Disk Tribometer for Evaluation of Traction and Scuffing of Lubricated Contacts,” Tribology Transactions, 62(3), 509-518, 2020.
- Hong, I. J., Kahraman, A., Anderson, N., “A Rotating Gear Test Methodology for Evaluation High-Cycle Tooth Bending Fatigue Lives under Fully Reversed and Fully Released Loading Conditions,” International Journal of Fatigue, 133, 105432, 2020.
- Nutakor, C., Talbot, D., Kahraman, A., “An Experimental Characterization of the Friction Coefficient of a Wind Turbine Gearbox Lubricant,” Wind Energy, 22, 509-522, 2019.
- Benatar, M., Handschuh, M, Kahraman, A., Talbot, D., “Static and Dynamic Transmission Error Measurements of Helical Gear Pairs With Various Tooth Modifications,” Journal of Mechanical Design, 141, 103301, 2019.
- Lee, H. K., Kim, M. S., Hong, S. M., Yoo, D. K, Kahraman, A., Talbot, D, “Research for the Modeling of the Dynamic Analysis for the Planetary Gear Sets under the Torque Fluctuation,” Trans. Korean Soc. Noise Vib. Eng., 29(4), 445-452, 2019.
- Hu, Y., Ryali, L., Talbot, D., Kahraman, A., “A Theoretical Study of the Overall Transmission Error in Planetary Gear Sets,” Journal of Mechanical Engineering Science, 0(0), I-12, 2019.
- Hu, Y., Talbot, D., Kahraman, A., “A Gear Load Distribution Model for a Planetary Gear Set with a Flexible Ring Gear Having External Splines,” Journal of Mechanical Design, 141, 53301, 2019.
- Polly, J., Talbot, D., Kahraman, A., Singh, A., Xu, H., “An Experimental Investigation of Churning Power Losses of a Gearbox,” Journal of Tribology, 140, 031102, 2018.
- Moss, J., Kahraman, A., Wink, C., “An Experimental Study of Influence of Lubrication Methods on Efficiency and Contact Fatigue Life of Spur Gears,” Journal of Tribology, 140, 051103, 2018.
- Hu, Y., Talbot, D., Kahraman, A., “A Load Distribution Model for Planetary Gear Sets,” Journal of Mechanical Design, 140, 053302, 2018.
- Leque, N.D., Kahraman, A., “A Three-dimensional Load sharing Model of Planetary Gear Sets Having Manufacturing Errors,” Journal of Mechanical Design, 139, 033302, 2017.
- Park, K., Harianto, J., Kahraman, A, “Prediction and Minimization of Mechanical Power Loss of Gear Pair via Analytical Approach,” Transactions of KSAE, 25(4), 498-507, 2017.
- Janakiraman, V., Kahraman, A., Talbot, D., “Modeling of Steady-State Mechanical Power Losses in Planetary Gear Trains of Automatic Transmissions,” Journal of Advanced Mechanical Design, Systems, and Manufacturing, 11(6), 2017.
- Benatar, M., Talbot, D., Kahraman, A., “An Experimental Investigation of Load Distribution of Spline Joint under Gear Loading Conditions,” Journal of Advanced Mechanical Design, Systems, and Manufacturing, 11(6), 2017.
- Kwon, H. S., Kahraman, A., “An Assemblability Check Methodology for the Kinematic Configurations of Automatic Transmission Planetary Gear Trains,” Journal of Mechanical Science and Technology, 30(12), 5606-5016, 2016.
- Talbot, D., Sun, A. , Kahraman, A., “Impact of Tooth Indexing Errors on Dynamic Factors of Spur Gears: Experiments and Model Simulation,” Journal of Mechanical Design, 138, 09.3302, 2016.
- Talbot, D., Kahraman, A., Li, S., Singh, A., Xu, H., “Development and Validation of a Model to Predict Power Losses of Automotive Axle Units,” Tribology Transactions, 59, 707-719, 2016.
- Hong, J., Talbot, D., Kahraman, A., “A Stiffness Formulation for Spline Joints,” Journal of Mechanical Design, 138, 043301-1, April 2016.
- Lee, H. K., Lee, S. H., Kim, M. S., Hong, S. A., Kim, S. W, Yoo, D. K, Kwon, H.S., Kahraman, A., “Development of a Design and Analysis Program for Automatic Transmission Applications to Consider the Planetary Gear Noise and Its Application,” Trans. Korean Soc. Noise Vib. Eng., 25(7), 487-495, 2015.
- Talbot, D., Kahraman, A., Stilwell, A.W., Singh, A., Napau, I., “Mechanical power losses of full-complement needle bearings of planetary gear sets: mode; and experiments,” Journal of Mechanical Engineering Science, 0(0), 1-17, March 2015.
- Kang, M. R. and Kahraman, A., “An experimental and theoretical study of the dynamic behavior of double-helical gear sets,” Journal of Sound and Vibration, 350, 11-29, April 2015.
- Hong, J., Talbot, D., Kahraman, A., “A Generalized Semi-Analytical Load Distribution Model for Clearance-fit, Major-fit, Minor-fit, and Mismatched Splines,” Journal of Mechanical Engineering Science, 10.1177, 0954406215603741, 2015.
- Hong, J., Talbot, D., Kahraman, A., “Effects of tooth indexing errors on load distribution and tooth load sharing of splines under combined loading conditions,” Journal of Mechanical Design, 137, 032601-1, March 2015.
- Talbot, D., Kahraman, A., and Seetharaman, S., “A Helical Gear Pair Pocketing Power Loss Model,” Journal of Tribology, 136, 021105, 2014.
- Park, D., Kolivand, M., Kahraman, A., “An Approximate Method to Predict Surface Wear of Hypoid Gears Using Surface Interpolation,” Mechanism and Machine Theory, 71, 64-78, 2014.
- Li, S. and Kahraman, A., “A Micro-pitting Model for Spur Gear Contacts,” International Journal of Fatigue, 59, 224-233, 2014.
- Kwon, H. S., Kahraman, A., Lee, H. K., Suh, H. S., “An Automated Design Search for Single and Double-Planet Planetary Gear Sets,” Journal of Mechanical Design, 136, 061004, 2014.
- Kahraman, A., Hilty, D.R., Singh, A., “An experimental investigation of spin power losses of a planetary gear set,” Mechanism and Machine Theory, 86, 48-61, December 2014.
- Janakiraman, V., Li, S., Kahraman, A., “An Investigation of the Impacts of Contact Parameters on Wear Coefficient,” Journal of Tribology, 136, 031602, 2014.
- Inalpolat, M., Handschuh, M., Kahraman, A., “Influence of indexing errors on dynamic response of spur gear pairs,” Mechanical Systems and Signal Processing, , November 2014.
- Hong, J., Talbot, D., Kahraman, A., “Load Distribution Analysis of Clearance-fit Spine Joints using Finite Elements,” Mechanisms and Machine Theory, 74, 42*57, 2014.
- Hong, J., Talbot, D., Kahraman, A., “A Semi-Analytical Load Distribution Model for Side-fit Involute Splines,” Mechanisms and Machine Theory, 76, 39-55, 2014.
- Handschuh, M. J., Kahraman, A., Milliren, M. R., “Impact of Tooth Spacing Errors on the Root Stresses of Spur Gear Pairs,” Journal of Mechanical Design, 136, 061010, 2014.
- Lee, H.K, Kim, M.S., Suh, H.S, Kim, J.H., Kahraman, A., Harianto, J., Kwon, H.S., “Research for development of a pRMC program for the Planetary Gear Noise,” Trans. Korean Soc. Noise Vib. Eng., 23(7), 669-674, 2013.
- Talbot, D., Li, S., and Kahraman, A., “Prediction of Mechanical Power Loss of Planet Gear Roller Bearings Under Combined Radial and Moment Loading,” ASME Journal of Mechanical Design, 135, 121007(11), December 2013.
- Sondkar, P. and Kahraman, A., “A Dynamic Model of a Double-helical Planetary Gear Set,” Mechanism and Machine Theory, 70, 157-174, 2013.
- Li, S., Kahraman, A., Anderson, N., and Wedeven, L. D., “A Model to Predict Scuffing Failures of a Ball-on-disk Contact,” Tribology International, 60, 233-245, 2013.
- Li, S. and Kahraman, A., “A Tribo-dynamic Model of a Spur Gear Pair,” Journal of Sound and Vibration, 332, 4963-4978, 2013.
- Li, S. and Kahraman, A., “Micro-pitting Fatigue Lives of Lubricated Point Contacts: Experiments and Model Validation,” International Journal of Fatigue, 48, 9-18, 2013.
- Li, S. and Kahraman, A., “A Physics-Based Model to Predict Micro-pitting Fatigue Lives of Lubricated Point Contacts,” International Journal of Fatigue, 47, 205-215, 2013.
- Hotait, M. and Kahraman, A., “Experiments on the Relationship between the Dynamic Transmission Error and the Dynamic Stress Factor of Spur Gear Pairs,” Mechanism and Machine Theory, 70, 116-128, 2013.
- Hotait, M. and Kahraman, A., “Estimation of Bending Fatigue Life of Hypoid Gears Using a Multi-axial Fatigue Criterion,” ASME Journal of Mechanical Design, 135, 101005(10), August 2013.
- Artoni, A., Guiggiani, M., Kahraman, A., and Harianto, J., “Robust Optimization of Cylindrical Gear Tooth Surface Modifications Within Ranges of Torque and Misalignments,” ASME Journal of Mechanical Design, 135, 121005(9), December 2013.
- Xu, H., Singh, A., Kahraman, A., Hurley, J., and Shon, S., “Effects of Bearing Preload, Oil Volume, and Operating Temperature on Axle Power Losses,” ASME Journal of Mechanical Design, 134, 054501(8), May 2012.
- Talbot, D., Kahraman, A., and Singh, A., “An Experimental Investigation of the Efficiency of Planetary Gear Sets,” ASME Journal of Mechanical Design, 134, 021003(7), February 2012.
- Park, D., Kolivand, M., Kahraman, A., “Prediction of Surface Wear of Hypoid Gears using a Semi-analytical Contact Model,” Mechanism and Machine Theory, 52, 180-194, 2012.
- Li, S., Kahraman, A., and Klein, M., “A Fatigue Model for Spur Gear Contacts Operating under Mixed Elastohydrodynamic Lubrication Conditions,” ASME Journal of Mechanical Design, 134, 041007(11), April 2012.
- Kang, M. R. and Kahraman, A., “Measurement of Vibratory Motions of Gears Supported by Compliant Shafts,” Mechanical Systems and Signal Processing, 29, 391-403, March 2012.
- Boguski, B., Kahraman, A., and Nishino, T., “A New Method to Measure Planet Load Sharing and Sun Gear Radial Orbit of Planetary Gear Sets,” ASME Journal of Mechanical Design, 134, 071002(8), July 2012.
- Xu, H., Singh, A., Maddock, D., Kahraman, A., and Hurley, J., “Thermal Mapping of an Automotive Rear Drive Axle,” SAE International, 4, April 2011.
- Li, S. and Kahraman, A., “A Method to Derive Friction and Rolling Power Loss Formulae for Mixed Elastohydrodynamic Lubrication,” JSME Journals, Journal of Advanced Mechanical Design, Systems, and Manufacturing, 5(4), 252-263, 2011.
- Li, S. and Kahraman, A., “Influence of Dynamic Behaviour on Elastohydrodynamic Lubrication of Spur Gears,” Journal of Engineering Tribology: IMech E, Part J, 225, 740-753, 2011.
- Li, S. and Kahraman, A., “A Spur Gear Mesh Interface Damping Model Based on Elastohydrodynamic Contact Behaviour,” International Journal of Powertrains, 1(1), 4-21, 2011.
- Li, S. and Kahraman, A., “A Fatigue Model for Contacts Under Mixed Elastohydrodynamic Lubrication Conditions,” International Journal of Fatigue, 33, 427-436, 2011.
- Kolivand, M. and Kahraman, A., “A General Approach to Locate Instantaneous Contact Lines of Gears Using Surface of Roll Angle,” ASME Journal of Mechanical Design, 133, 014503(6), January 2011.
- Hotait M., Kahraman, A. and Nishino, T., “An Investigation of Root Stresses of Hypoid Gears with Misalignments,” ASME Journal of Mechanical Design, 133, 071006(9), July 2011.
- Artoni, A., Gabiccini, M., Guiggiani, M., Kahraman A., “Multi-Objective Ease-off Optimization of Hypoid Gears for Their Efficiency, Noise, and Durability Performances,” ASME Journal of Mechanical Design, 133, 121007(9), December 2011.
- Seetharaman, S. and Kahraman, A., “A Windage Power Loss Model for Spur Gear Pairs,” Tribology Transactions, 53, 473-484, 2010.
- Li, S. and Kahraman, A., “Prediction of Spur Gear Mechanical Power Losses Using a Transient Elastohydrodynamic Lubrication Model,” Tribology Transactions, 53, 554-563, 2010.
- Li, S. and Kahraman, A., “A Transient Mixed Elastohydrodynamic Lubrication Model for Spur Gear Pairs,” Journal of Tribology, 132, 011501(9), January 2010.
- Kolivand, M., Li, S., and Kahraman, A., “Prediction of Mechanical Gear Mesh Efficiency of Hypoid Gear Pairs,” Mechanism and Machine Theory, 45, 1568-1582, 2010.
- Kolivand, M. and Kahraman, A., “An Ease-Off Based Method for Loaded Tooth Contact Analysis of Hypoid Gears Having Local and Global Surface Deviations,” ASME Journal of Mechanical Design, 132, 071004(8), July 2010.
- Kahraman, A., Ligata, H., and Singh, A., “Influence of Ring Gear Rim Thickness on Planetary Gear Set Behavior,” ASME Journal of Mechanical Design, 132, 021002(8), February 2010.
- Kahraman, A. and Ding, H., “A Methodology to Predict Surface Wear of Planetary Gears under Dynamic Conditions,” Mechanics Based Design of Structures and Machines, 38, 493-515, 2010.
- Inalpolat, M. and Kahraman, A., “A Dynamic Model to Predict Modulation Sidebands of a Planetary Gear Set Having Manufacturing Errors,” Journal of Sound and Vibration, 329, 371-393, 2010.
- Artoni, A., Kolivand, M., and Kahraman, A., “An Ease-Off Based Optimization of the Loaded Transmission Error of Hypoid Gears,” ASME Journal of Mechanical Design, 132, 011010(9), January 2010.
- Seetharaman, S., Kahraman, A., Moorhead, M., and Petry-Johnson, T., “Oil Churning Power Losses of a Spur Gear Pair: Experiments and Model Validation,” ASME Journal of Tribology, 131, 022202(10), April 2009.
- Seetharaman, S. and Kahraman, A., “Load-Independent Power Losses of a Spur Gear Pair: Model Formulation,” ASME Journal of Tribology, 131, 022201(11), April 2009.
- Park, D. and Kahraman, A., “A Surface Wear Model for Hypoid Gears,” Wear, 267, 1595-1604, 2009.
- Ligata, H., Kahraman, A., and Singh, A., “Closed-Form Planet Load Sharing Formulation for Planetary Gear Sets Using a Translational Analogy,” ASME Journal of Mechanical Design, 131, 021007(7), February 2009.
- Li, S., Vaidyanathan, A., Harianto, J., and Kahraman, A., “Influence of Design Parameters on Mechanical Power Losses of Helical Gear Pairs,” JSME Journals, Journal of Advanced Mechanical Design, Systems, and Manufacturing, 3(2), 146-158, 2009.
- Li, S. and Kahraman, A., “A Mixed EHL Model with Asymmetric Integrated Control Volume Discretization,” Tribology International, 42, 1163-1172, June 2009.
- Kolivand, M. and Kahraman, A., “A Load Distribution Model for Hypoid Gears Using Ease-Off Topography and Shell Theory,” Mechanism and Machine Theory, 44, 1848-1865, 2009.
- Inalpolat, M. and Kahraman, A., “A Theoretical and Experimental Investigation of Modulation Sidebands of Planetary Gear Sets,” Journal of Sound and Vibration, 323, 677-696, 2009.
- Singh, A., Kahraman, A., and Ligata, H., “Internal Gear Strains and Load Sharing in Planetary Transmissions: Model and Experiments,” ASME Journal of Mechanical Design, 130, 072602(10), July 2008.
- Petry-Johnson, T., Kahraman, A., Anderson, N.E., and Chase, D., “An Experimental Investigation of Spur Gear Efficiency,” ASME Journal of Mechanical Design, 130(6), 062601(10), June 2008.
- McFerran, J., West, J., Subramaniam, V. V., and Kahraman, A., “Response of an Isolated Particulate Subjected to Lateral Electric Fields in a DC Glow Discharge,” IEEE Transactions on Plasma Science, 36(5), 2838-2850, October 2008.
- Ligata, H., Kahraman, A., and Singh, A., “An Experimental Study of the Influence of Manufacturing Errors on the Planetary Gear Stresses and Planet Load Sharing,” ASME Journal of Mechanical Design, 130(4), 041701(9), April 2008.
- Inalpolat, M. and Kahraman, A., “Dynamic Modelling of Planetary Gears of Automatic Transmissions,” Proc. IMechE, Part K: Journal of Multi-Body Dynamics, 222(3), 229-242, 2008.
- Hotait, M. and Kahraman, A., “Experiments on Root Stresses of Helical Gears with Lead Crown and Misalignments,” ASME Journal of Mechanical Design, 130, 074502(5), July 2008.
- Xu, H., Kahraman, A., Anderson, N.E., and Maddock, D., “Prediction of Mechanical Efficiency of Parallel-Axis Gear Pairs,” ASME Journal of Mechanical Design, 129, 58-68, January 2007.
- Xu, H. and Kahraman, A., “Prediction of Friction-Related Power Losses of Hypoid Gear Pairs,” Proc. IMechE, Part K: Journal of Multi-Body Dynamics, 221(3), 387-400, 2007.
- Tamminana, V. K., Kahraman A., and Vijayakar, S., “A Study of the Relationship between the Dynamic Factors and the Dynamic Transmission Error of Spur Gear Pairs,” ASME Journal of Mechanical Design, 129, 75-84, January 2007.
- Ma, Q., Kahraman, A., Perret-Liaudet, J., and Rigaud, E., “An Investigation of Steady-State Dynamic Response of a Sphere-Plane Contact Interface with Contact Loss,” ASME Journal of Applied Mechanics, 74(2), 249-255, March 2007.
- Espin, S., Perret-Liaudet J., and Kahraman, A., “Etude Theorique et Experimentale du Comportement non Lineaire d’un Engrenage Droit Induit par le Jeu Entre Dents,” Mecanique & Industries, 8, 365-377, 2007.
- Ding, H. and Kahraman, A., “Interactions Between Nonlinear Spur Gear Dynamics and Surface Wear,” Journal of Sound and Vibration, 307, 662-679, 2007.
- Al-shyyab, A. and Kahraman, A., “A Non-Linear Dynamic Model for Planetary Gear Sets,” Proc. IMechE, Part K: Journal of Multi-Body Dynamics, 221, 567-576, 2007.
- Ma, Q. and Kahraman, A., “Subharmonic Resonances of a Mechanical Oscillator with Periodically Time-Varying, Piecewise-Nonlinear Stiffness,” Journal of Sound and Vibration, 294(3), 624-636, 2006.
- Ma, Q. and Kahraman, A., “Period-One Motions of a Mechanical Oscillator with Periodically Time-Varying, Piecewise-Nonlinear Stiffness,” Journal of Sound and Vibration, 284, 893-914, 2005.
- Kahraman, A., Bajpai, P., and Anderson, N., “Influence of Tooth Profile Deviations on Helical Gear Wear,” ASME Journal of Mechanical Design, 127, 656-663, July 2005.
- Al-shyyab, A. and Kahraman, A., “Non-Linear Dynamic Analysis of a Multi-Mesh Gear Train using Multi-Term Harmonic Balance Method: Sub-Harmonic Resonances,” Journal of Sound and Vibration, 279, 417-451, 2005.
- Al-shyyab, A. and Kahraman, A., “Non-Linear Dynamic Analysis of a Multi-Mesh Gear Train using Multi-Term Harmonic Balance Method: Period-One Motions,” Journal of Sound and Vibration, 284, 151-172, 2005.
- Yuksel, C. and Kahraman, A., “Dynamic Tooth Loads of Planetary Gear Sets Having Tooth Profile Wear,” Mechanism and Machine Theory, 39, 695-715, 2004.
- Moraru, L., Keith Jr., T.G., and Kahraman, A., “Aspects Regarding the Use of Probabilistic Models for Isothermal Full Film Rough Line Contacts,” Tribology Transactions, 47, 386-395, 2004.
- Kubur, M., Kahraman, A., Zini, D., and Kienzle, K., “Dynamic Analysis of a Multi-Shaft Helical Gear Transmission by Finite Elements: Model and Experiment,” ASME Journal of Vibrations and Acoustics, 126, 398-406, July 2004.
- Krantz, T. and Kahraman, A., “An Experimental Investigation of the Influence of the Lubricant Viscosity and Additives on Gear Wear,” Tribology Transactions, 47, 138-148, 2004.
- Kahraman, A., Ligata, H., Kienzle, K., and Zini, D., “A Kinematics and Power Flow Analysis Methodology for Automatic Transmission Planetary Gear Trains,” ASME Journal of Mechanical Design, 126, 1071-1081, November 2004.
- Bodas, A. and Kahraman, A., “Influence of Carrier and Gear Manufacturing Errors on the Static Load Sharing Behavior of Planetary Gear Sets,” JSME International Journal, Series C, 47(3), 908-915, 2004.
- Bajpai, P., Kahraman, A., and Anderson, N. E., “A Surface Wear Prediction Methodology for Parallel-Axis Gear Pairs,” ASME Journal of Tribology, 126, 597-605, July 2004.
- Kahraman, A., Kharazi, A. A., and Umrani, M., “A Deformable Body Dynamic Analysis of Planetary Gears with Thin Rims,” Journal of Sound and Vibration, 262, 752-768, 2003.
- Wagaj, P. and Kahraman, A., “Influence of Tooth Profile Modification on Helical Gear Durability,” ASME Journal of Mechanical Design, 124, 501-510, September 2002.
- Su, X., Menq, C.H., and Houser, D.R., “Estimation of Reference Misalignment of a Spur Gear and its Application to Profile and Lead Measurement,” Journal of Manufacturing Science and Engineering, 124(2), 333-340, May 2002.
- Cioc, C., Cioc, S., Moraru, L., Kahraman, A., and Keith, T., “A Deterministic Elastohydrodynamic Lubrication Model of High-Speed Rotorcraft Transmission Components,” Tribology Transactions, 45, 556-562, 2002.
- Kahraman, A. and Vijayakar, S., “Effect of Internal Gear Flexibility on the Quasi-Static Behavior of a Planetary Gear Set,” ASME Journal of Mechanical Design, 123, 408-415, September 2001.
- Kahraman, A., “Free Torsional Vibration Characteristics of Compound Planetary Gear Sets,” Mechanism and Machine Theory, 36, 953-971, 2001.
- Kahraman, A., “A Spline Joint Formulation for Drive Train Torsional Dynamic Models,” Journal of Sound and Vibration, 241(2), 328-336, 2001.
- Su, X. and Houser, D. R., “Characteristics of Trochoids and their Application to Determining Gear Teeth Fillet Shapes,” Mechanism and Machine Theory, 35(2), 291-304, 2000.
- Su, X. and Houser, D. R., “Alternative Equation of Meshing for Worm-Gear Drives and its Application to Determining Undercutting and Reverse Engineering,” ASME Journal of Mechanical Design, 122(2), 207-212, June 2000.
- Luscher, A. and Houser, D., “An Investigation of the Geometry and Transmission Error of Injection Molded Gears,” Journal of Injection Molding Technology, 4, 177-190, December 2000.
- Lim, T.C., Li, J., “Dynamic Analysis of Multi-Mesh Counter-Shaft Transmission,” Journal of Sound and Vibration, 215(5), 905-919, July 1999.
- Singh, A., Houser, D. R., and Vijayakar, S., “Detecting Gear Tooth Breakage Using Acoustic Emission: a Feasibility and Sensor Placement Study,” ASME Journal of Mechanical Design, 121(4), 587-593, December 1999.
- Kahraman, A. and Blankenship, G. W., “Effect of Involute Tip Relief on Dynamic Response of Spur Gear Pair,” ASME Journal of Mechanical Design, 121, 313-315, June 1999.
- Kahraman, A. and Blankenship, G. W., “Effect of Involute Contact Ratio on Spur Gear Dynamics,” ASME Journal of Mechanical Design, 121, 112-118, March 1999.
- Kahraman, A. and Blankenship, G. W., “Experiments on Nonlinear Dynamic Behavior of an Oscillator with Clearance and Time-Varying Parameters,” ASME Journal of Applied Mechanics, 64, 217-226, March 1997.
- Matson, G.A., Houser, D.R., “The Use of Ghost Noise as an Exciter for High Frequency Gear System Dynamics,” VDI Berichte, 1230, 739-750, 1996.
- Kahraman, A. and Blankenship, G. W., “Interactions Between Commensurate Parametric and Forcing Excitations in a System with Clearance,” Journal of Sound and Vibration, 194, 317-336, 1996.
- Kahraman, A., “General Procedure for Life Prediction and Durability Testing of Automatic Transmission Gear Trains,” General Motors Research, , January 1995.
- Blankenship, G. W. and Kahraman, A., “Steady State Forced Response of a Mechanical Oscillator with Combined Parametric Excitation and Clearance Type Non-Linearity,” Journal of Sound and Vibration, 185, 743-765, 1995.
- Vaidyanathan, S., Busby, H.R., and Houser, D. R., “A Numerical Approach To The Static Analysis of an Annular Sector Mindlin Plate with Applications to Bevel Gear Design,” Computers and Structures, 51(3), 255-266, 1994.
- Kahraman, A., “Load Sharing Characteristics of Planetary Transmissions,” Mechanism and Machine Theory, 29, 1151-1165, 1994.
- Kahraman, A., “Natural Modes of Planetary Gear Trains,” Journal of Sound and Vibration, 173, 125-130, 1994.
- Kahraman, A., “Planetary Gear Train Dynamics,” ASME Journal of Mechanical Design, 116, 713-720, September 1994.
- Kahraman, A., “Dynamic Analysis of a Multi-Mesh Helical Gear Train,” ASME Journal of Mechanical Design, 116, 706-712, September 1994.
- Daniewicz, S. R., Collins, J. A., and Houser, D. R., “An Elastic-Plastic Analytical Model for Predicting Fatigue Crack Growth in Arbitrary Edge-Cracked Two-Dimensional Geometries with Residual Stress,” ASME Journal of Mechanical Design, 16, 123-134, February 1994.
- Stegemiller, M. E. and Houser, D. R., “A Three-Dimensional Analysis of the Base Flexibility of Gear Teeth,” ASME Journal of Mechanical Design, 115(1), 186-192, March 1993.
- Kahraman, A., “Effect of Axial Vibrations on the Dynamics of a Helical Gear Pair,” ASME Journal of Vibration and Acoustics, 115, 33-39, 1993.
- Kahraman, A., Ozguven, H. N., Houser, D. R., and Zakrajsek, J. J., “Dynamic Analysis of Geared Rotors by Finite Elements,” ASME Journal of Mechanical Design, 114, 507-514, September 1992.
- Kahraman, A. and Singh, R., “Dynamics of an Oscillator with Both Clearance and Continuous Non-Linearities,” Journal of Sound and Vibration, 153, 180-185, 1992.
- Kahraman, A., “On the Response of a Preloaded Mechanical Oscillator with a Clearance: Period-Doubling and Chaos,” Nonlinear Dynamics, 3, 183-198, 1992.
- Kahraman, A., “Gear Rattle Analysis of the Freedom Vehicle Drive-Wheel Assembly,” General Motors Research, 237, 177, May 1991.
- Sundaresan, S., Ishii, K., and Houser, D.R., “A Procedure Using Manufacturing Variance to Design Gears with Minimum Transmission Error,” ASME Journal of Mechanical Design, 113(3), 318-324, September 1991.
- Kahraman, A. and Singh, R., “Nonlinear Dynamic Analysis of a Geared Rotor-Bearing System with Multiple Clearances,” Journal of Sound and Vibration, 144, 469-506, 1991.
- Kahraman, A. and Singh, R., “Interactions Between Time-Varying Mesh Stiffness and Clearance Non-Linearities in a Geared System,” Journal of Sound and Vibration, 146, 135-156, 1991.
- Kahraman, A. and Singh, R., “Error Associated with a Reduced Order Linear Model of a Spur Gear Pair,” Journal of Sound and Vibration, 149, 495-498, 1991.
- Kahraman, A. and Singh, R., “Nonlinear Dynamics of a Spur Gear Pair,” Journal of Sound and Vibration, 142, 49-75, 1990.
- Houser, D.R, Young, W., Kinzel, G.L., Rajab, M., “Force Transmissibility Through Rolling Contact Bearings,” IMAC, , 1989.
- Houser, D.R., Duraisamy, S., Heyd, R., Sanzo, R., “Optimal Root Geometry and Fatigue Testing of Spur Gears,” , , August 1988.
- Vijayakar, S., Busby, H.R., and Houser, D.R., “Linearization of Multibody Frictional Contact Problems,” Computers and Structures, 29(4), 596-576, 1988.
- Özguven, H.N., and Houser, D.R., “Mathematical Models used in Gear Dynamics – a Review,” Journal of Sound and Vibration, 121(3), 383-411, 1988.
- Özguven, H.N., and Houser, D.R., “Dynamic Analysis of High Speed Gears by Using Loaded Static Transmission Error,” Journal of Sound and Vibration, 125(1), 71-73, 1988.
- Vijayakar, S., Busby, H.R., and Houser, D.R., “Finite Element Analysis of Quasi-Prismatic Bodies Using Chebyshev Polynomials,” International Journal for Numerical Methods in Engineering, 24(8), 1461-1477, 1987.
- Houser, D.R., “The Root of Gear Noise Transmission Error,” Power Transmission Design, , May 1986.
- Tavakoli, M.S., and Houser, D.R., “Optimum Profile Modifications for the Minimization of Static Transmission Errors of Spur Gears,” Journal of Mechanisms, Transmissions, and Automation in Design, 108(1), 86-95, 1986.
- Houser, D.R., “Gear Dynamics and Gear Noise Research Laboratory,” SAE Technical Paper, , 821066, September 1982.
- Houser, D.R., “Practical Strain Gage Bridge Guide,” , , September 1981.
- Seireg, A. and Houser, D.R., “Evaluation of Dynamic Factors for Spur and Helical Gears,” Journal of Engineering for Industry, , 504-515, May 1970.
- Houser, D.R. and Seireg, A., “An Experimental Investigation of Dynamic Factors in Spur and Helical Gears,” Journal of Engineering for Industry, , 495-503, May 1970.
- Michael Benatar, “A Dynamic Load Distribution Model of Helical Gear Pairs Having Various Manufacturing Errors”, PhD. 2022
- Ata Donmez, “Theoretical and Experimental Investigation of Vibro-impacts of Drivetrains Subjected to External Torque Fluctuations”, PhD. 2021
- Colton Thomas, “An Experimental Methodology for Evaluating Root Stresses of Rattling Gear Pairs”, MSc. 2021
- Gunther Beall, “An Experimental Methodology for Evaluating Root Stresses of Rattling Gear Pairs”, MSc. 2021
- Emily Aneshansley, “Applied Statistical Mircocontact Model for the Prediction of Gear Power Loss”, MSc. 2021
- Lokaditya Ryali, “A Dynamic Load Distribution Model of Planetary Gear Sets”, PhD. 2021
- Ahmet Dindar, “An Experimental and Theoretical Investigation of Tribo-Dynamic Behavior and Power Losses of Ball Bearings”, PhD. 2021
- Suhas Ashok Kedilaya, “A Study on the Long Cycle Micro-Pitting Behavior of Spur Gear Pairs”, MSc. 2021
- Qihang Zeng, “On the Influence of Surface and Elastohydrodynamic Lubrication Parameters on Pitting Lives of Spur Gears”, MSc. 2021
- Rob McEwan, “A Case Study on the Impact of Web Flexibility on Quasi-Static and Dynamic Behavior of a Spur Gear Pair of Gear Surface Pitting”, MSc. 2021
- Eunsung Kim, “An Investigation of the Influence of Micropitting on the Progression of Gear Surface Pitting”, MSc. 2021
- Haelie Egbert, “Application of Acoustic Emissions and High-Speed Imaging Techniques to Detect Gear Tooth Bending Fatigue Damage”, MSc. 2021
- Cihan Alper Celikay, “An Experimental and Theoretical Study of Subharmonic Resonances of a Spur Gear Pair”, MSc. 2021
- Zachary Teaford, “An Experimental Investigation on the Influence of Tensile Mean Stress on Gear Tooth Bending Fatigue Life”, MSc. 2020
- Amit S. Chimanpure, “A Generalized Elastohydrodynamic Lubrication Model for Two-Dimensional Contacts”, PhD. 2020
- Aravind Srinivasan, “Development of an Experimental Methodology for Single-Tooth Bending Fatigue Evaluation of Spur Gears”, MSc. 2020
- Ayush Garg, “Experimental and Theoretical Investigation of Drag Power Losses of Gears with and without Enclosures”, MSc. 2020
- Harnavpreet Gill, “Computationally Robust Algorithms for Hypoid Gear Cutting and Contact Line Determination using Ease-Off Methodology”, MSc. 2020
- Abhishek Suresan, “Load Distribution Modeling of Asymmetric Involute Gear Pairs”, MSc. 2020
- Altug Guner, “Measurement of Power Losses of Rolling Element Bearings under Tightly-Controlled Temperature and Loading Conditions”, PhD. 2020
- Muhammad Nevin Anandika, “An Experimental Investigation of the Impact of Random Spacing Errors on the Transmission Error of Spur and Helical Gear Pairs”, MSc. 2019
- Ishan Mann, “Contact Fatigue Evaluation of Super Honed Spur Gears Made of Aisi 4118 Alloy Steel”, MSc. 2019
- Thomas Gullo, “A Methodology to Evaluate the Dynamic Behavior of Back-To-Back Test Machines”, MSc. 2019
- Kreteeka Chaudhury, “An Experimental Investigation of the Impact of Engineered Surface Processes on Efficiency of Spur Gears”, MSc. 2019
- Siddhartha Govilkar, “Development of a New Test Machine for Experimental Contact Fatigue Investigations of Spur Gears”, MSc. 2019
- Isaac Hong, “Impact of the Fully Reversed Loading Condition on Gear Tooth Bending Strength”, PhD. 2018
- Michael James Handschuh, “A Methodology to Establish Scuffing Limits for Lubricated Point Contacts Subject to Sliding”, PhD. 2018
- Tiffany Wen Roe Lim, “An Experimental Study on the Effects of Debris Damage on Scuffing Performance of Spur Gear Pairs”, MSc. 2018
- Kevin G. Vedera, “An Experimental Methodology for Evaluating Power Losses of Rolling Element Bearings Subjected to Combined Radial and Axial Loads”, MSc. 2018
- Kyler T. McDonald, “An Experimental Study of Spin Power Losses of a High-Speed Gearbox”, MSc. 2018
- Tiffany W.R. Lim, “An Experimental Study on the Effects of Debris Damage on Scuffing Performance of Spur Gear Pairs”, MSc. 2018
- Sarah Case, “Instantaneous Kinematic Analyses of Spur and Helical Gear Pairs Having Runout and Wobble Errors”, MSc. 2018
- Preetish Jaiswal, “Influence of Various Surface Treatments on Power Losses of Spur Gear Pairs”, MSc. 2017
- Yong Hu, “A Load Distribution Model of Planetary Gear Sets”, PhD. 2017
- Jeremy C. Moss, “A Comparative Study of the Impact of Dip and Jet Lubrication Methods on Spur Gear Contact Fatigue and Efficiency”, MSc. 2016
- Hugo Blettery, “An Experimental Study of the Influence of Misalignments on the Loaded Transmission Error and Root Stresses of Hypoid Gear Pairs”, MSc. 2016
- Jiazheng Hong, “A Semi-Analytical Load Distribution Model of Spline Joints”, PhD. 2015
- Allen Y. Sun, “An Experimental Study of the Dynamic Response of Spur Gears Having Tooth Index Errors”, MSc. 2015
- Nick Leque, “Development of Load Sharing Models for Double-Helical Epicyclic Gear Sets”, PhD. 2015
- Maru Kang, “A Study of Quasi-Static and Dynamic Behavior of Double-Helical Gears”, PhD. 2014
- Rohit Abraham, “An Experimental Study of Scuffing Performance of a Helical Gear Pair Subjected to Different Lubrication Methods”, MSc. 2014
- Nial Tilson, “An Experimental Evaluation of Micro-Pitting Performance of Two Bearing Steels”, MSc. 2013
- Niranjan P. Raghuraman, “A Calculation Procedure to Account for Transient Temperature, Humidity and Tolerance in the Load Distribution Analysis of Plastic and Metal Gears”, MSc. 2013
- Joseph H. Polly, “An Experimental Investigation of Churning Power Losses of a Gearbox”, MSc. 2013
- Hyun Sik Kwon, “Development of Automated Design Tools for Automotive Automatic Transmission Gear System”, PhD. 2013
- VenkataKrishna Janakiraman, “An Investigation of the Impact of Contact Parameters on the Wear Coefficient”, MSc. 2013
- Michael James Handschuh, “An Investigation into the Impact of Random Spacing Errors on Static Transmission Error and Root Stresses of Spur Gear Pairs”, MSc. 2013
- Justin Michael Franzen, “Contact Fatigue Evaluation of Ground and Chemically Polished Spur Gears Made of Aisi 4118 Alloy Steel”, MSc. 2013
- James Walter Brenneman, “An Experimental Study on the Scuffing Performance of High-Power Spur Gears at Elevated Oil Temperatures”, MSc. 2013
- Jason Louis Austin, “A Multi-Component Analysis of a Wind Turbine Gearbox using a High Fidelity Finite Element Model”, MSc. 2013
- Samuel Shon, “An Experimental Study on the Impact of Various Surface Treatments on Friction, Scuffing and Wear Characteristics of Lubricated Rolling-Sliding Contacts”, MSc. 2012
- Steve Wilson, “Traction and Wear Evaluation of a Number of Plastic Materials and Greases under Combined Rolling and Sliding Contact Conditions”, MSc. 2012
- David Talbot, “An Experimental and Theoretical Investigation of the Efficiency of Planetary Gear Sets”, PhD. 2012
- Alex Stilwell, “An Experimental Study of Power Losses of Full-Complement Needle Bearings of Planetary Gear Sets”, MSc. 2012
- Prashant Sondkar, “Dynamic Modeling of Double-Helical Planetary Gear Sets”, PhD. 2012
- Thomas J. Prewitt, “Quasi-Static, Deformable-Body Analysis of a Face Gear-Thrust Bearing System”, MSc. 2012
- David Pickens, “Experimental Assessment of the Dynamic Factors of Fzg Gear Tests as Well as an Evaluation of a Micropitting Load Capacity Formula”, MSc. 2012
- Garrett Olson, “Experiments on the High-Power and High-Temperature Performance of Gear Contacts”, MSc. 2012
- Sriram Madhavan, “A Study of Geometry and Deformable-Body Characteristics of Non-Right Angle Worm Gear Pairs”, MSc. 2012
- Erdem Erkilic, “A Model to Predict Pocketing Power Losses in Spiral Bevel and Hypoid Gears”, MSc. 2012
- Anindo Banerjee, “A Model to Predict Sun Gear Radial Orbit of a Planetary Get Set having Manufacturing Errors”, MSc. 2012
- Aaron Thaler, “A High Fidelity Finite Element and Contact Analysis Investigation of Stresses and Motions of a Wind Turbine Gearbox”, MSc. 2011
- Matthew B. Milliren, “An Experimental Investigation of the Influence of Various Gear Steels on the Contact Fatigue Lives of Hard Ground Spur Gears”, MSc. 2011
- Mark R. Milliren, “An Experimental Investigation Into the Influence of Various Errors on the Transmission Error and Root Stresses of Spur Gears”, MSc. 2011
- Nick Leque, “Development of an Experimental Methodology for Evaluation of Gear Contact Fatigue under High-Power and High-Temperature Conditions”, MSc. 2011
- Sumanth Kashyap, “Development of a Procedure to Describe Plastic Gear Geometry After a Temperature Change with Application to the Prediction of Gear Load Distribution”, MSc. 2011
- Mohammad Hotait, “A Theoretical and Experimental Investigation on Bending Strength and Fatigue Life of Spiral Bevel and Hypoid Gears”, PhD. 2011
- Aaron Sanders, “An Experimental Investigation of the Influence of Elliptical Root Shapes and Asymmetric Teeth on Root Stresses and Bending Fatigue Lives”, MSc. 2010
- Sandeep Makam, “An Experimental Study on the Influence of Misalignments on the Static Transmission Error of Hypoid Gear Pairs”, MSc. 2010
- Joewen Liu, “A Theoretical and Experimental Investigation of Roller and Gear Scuffing”, PhD. 2010
- Devin Hilty, “An Experimental Investigation of Spin Power Losses of Planetary Gear Sets”, MSc. 2010
- Brian Boguski, “An Experimental Investigation of the System–Level Behavior of Planetary Gear Sets”, MSc. 2010
- Aarthy Vidyanathan, “An Experimental Investigation of Helical Gear Efficiency”, MSc. 2009
- Satya Seetharaman, “An Investigation of Load-independent Power Losses of Gear Systems”, PhD. 2009
- Daehyun Park, “Development of Surface Wear and Lapping Simulation Models for Hypoid Gears”, PhD. 2009
- Karthikeyan R Marambedu, “Development of a Procedure for the Analysis of Load Distribution, Stresses and Transmission Error of Straight Bevel Gears Gears having Local and Global Surface Deviations”, MSc. 2009
- Sheng Li, “Lubrication and Contact Fatigue Models for Roller and Gear Cotnacts”, PhD. 2009
- Mohsen Kolivand, “Development of Tooth Contact and Mechanical Efficiency Models for Face-Milled and Face-Hobbed Hypoid and Spiral Bevel Gears”, PhD. 2009
- Mark Klein, “An Experimental Investigation of Materials and Surface Treatments on Gear Contact Fatigue Life of Roller and Gear Scuffing”, MSc. 2009
- Maru Kang, “Measurement of Vibrations of Gears Supported By Compliant Shafts”, MSc. 2009
- Murat Inalpolat, “A Theoretical and Experimental Investigation of Modulation Sidebands of Planetary Gear Sets”, PhD. 2009
- Josh Hurley, “An Experimental Investigation of Thermal Behavior of an Automotive Rear Axle”, MSc. 2009
- Steven Harpster, “A Feasibility Study on Development of Dust Abrasion Resistant Gear Concepts for Lunar Vehicle Gearboxes”, MSc. 2009
- Zachary H. Wright, “Loaded Transmission Error Measurement System for Spur and Helical Gears”, MSc. 2008
- Timothy A. Szweda, “An Experimental Study of Power Losses of an Automotive Manual Transmission”, MSc. 2008
- David Talbot, “Finite Element Analysis of Geared Shaft Assemblies and Thin-Rimmed Gears”, MSc. 2007
- Travis T. Petry-Johnson, “Experimental Investigation of Spur Gear Efficiency”, MSc. 2007
- Ji Youp Park, “Plastic Gear Surface Temperature and Wear Behavior”, MSc. 2007
- Michael D. Moorhead, “Experimental Investigation of Spur Gear Efficiency and The Development of a Helical Gear Efficiency Test Machine”, MSc. 2007
- Haris Ligata, “Impact of System-Level Factors on Planetary Gear Set Behavior”, PhD. 2007
- Mohammad Hotait, “Influence of Shaft Misalignments On Root Stresses of Helical Gears With Lead Crown”, MSc. 2007
- Michael D. Heskamp, “Development of a Digital Data Acquisition and Analysis System for The Measurement of Dynamic Transmission Error of Spur and Helical Gear Pairs”, MSc. 2007
- Huali Ding, “A Study of Interactions between Dynamic Bevahior of Gear Systems and Surface Wear”, PhD. 2007
- Jeremy Bluestein, “An Experimental Study of the Impact of Various Tooth Surface Treatments on Spur Gear Pitting Life”, MSc. 2007
- Jae Hyuk Lim, “A Dynamic Model of a Spur Gear Pair With Contact Friction”, MSc. 2006
- Hai Xu, “Development of a Generalized Mechanical Efficiency Prediction Methodology for Gear Pairs”, PhD. 2005
- Venkata (Krishna) Tamminana, “A Study on the Relationship between the Dynamic Factor and The Dynamic Transmission Error of Spur Gear Pairs”, MSc. 2005
- Aaron Schmitkons, “Loaded Bevel Gear Static Transmission Error Test Stand Redesign and Assessment”, MSc. 2005
- Hubert Ma, “A Study of the Dynamic Behavior of Piecewise Nonlinear Oscillators with Time-Varying Stiffness”, PhD. 2005
- Tom Schachinger, “The Effects of Isolated Transmission Error, Force Shuttling, and Frictional Excitations On Gear Noise and Vibration”, MSc. 2004
- Jae Yeol Park, “Gear Mesh and Gear Support System Analysis using a Finite Element Geared Shaft Model”, MSc. 2004
- Feng Liu, “Face Gear Design and Compliance Analysis”, MSc. 2004
- Lisa Ghezzi, “Multiple Mesh Gear optimization Procedures using Run Many Cases”, MSc. 2004
- Akash Chaudhuri, “Reduced Geometric Error of Gears Via Gas-Assisted Injection Molding”, MSc. 2004
- Abhinav Bajpai, “The Effect of Gear Geometry and Surface Finish on Measured Transmission Error and Noise for Several Gear Sets”, MSc. 2004
- Venkataraman Kartik, “Analytical Prediction of Load Distribution and Transmission Error for Multiple-Mesh Gear-Trains and Dynamic Studies in Gear Noise and Vibration”, MSc. 2003
- Tugan Eritenel, “Development of a Three Dimensional Dynamic Load Distribution Program”, MSc. 2003
- Muquarram Colabawala, “A Study of Gear Whine Noise Acquisition and Analysis Techniques”, MSc. 2003
- Eddy Sugyarto, “The Kinematic Study, Geometry Generation, and Load Distribution Analysis of Spiral Bevel and Hypoid Gears”, MSc. 2002
- Sean Wright, “Face Gear Contact Analysis Program Development Using the Thin Slice Method”, MSc. 2001
- Husni Wijaya, “Effect of Spacing Errors and Runout on Transverse Load Sharing and Dynamic Factors and Idler Gear Dynamic Analysis”, MSc. 2001
- Manish Vaishya, “Vibro-Acoustic Characteristics of Sliding Friction in Geared Rotor Systems”, PhD. 2001
- Satyanarayana Merugu, “Analysis of Geared Shaft Configurations and Thin Rimmed Gears Using Finite Element Method”, MSc. 2001
- Daria Kotys, “Improving Gear Accuracy through Gas-Assisted Injection Molding”, MSc. 2001
- Chalermpong Boonsue, “Comparison of the Effect of Input Variables of the Performance of Optimization Programs, General and Eval4”, MSc. 2001
- David Binney, “Generation of Face Gear Geometry for Kinematic Study and Loaded Analysis”, MSc. 2001
- Chris Snow, “An Investigation of the Geometry, Transmission Error and Noise of Injection Molded Gears”, MSc. 2000
- Brandon Roesti, “Refinements in Root Stress Analyis, Modeling and Simulation of Several Spur and Helical Gear Sets”, MSc. 2000
- Bryan O’Harra, “Static and Dynamic Analysis of the Variable Center Distance Test Rig”, MSc. 2000
- Yuping Cheng, “Dynamics of Hypoid and Bevel Geraed Rotor Systems”, PhD. 2000
- Xiaogen Su, “Generation, Measurement and Reverse Engineering of Three-Dimensional Gears”, PhD. 1999
- Gary R. Poling, “Hypoid Gear Test Rig Transmission Error Measurement Enhancement and Topics in Root Stresses of Several Gear Types”, MSc. 1999
- Ashley Dunn, “Methods for Researching Gear Whine in Automotive Transmissions”, MSc. 1999
- Isaias C. Regalado, “Application of Robustness in the Multi-Objective Optimization of Gears”, PhD. 1998
- Gandhi Gopinath, “Analysis of Geared Shafts Using Finite Element Techniques”, MSc. 1998
- Avinashchandra Singh, “An Experimental and Numerical Investigation of Stress Wave Propagation Across Interfaces”, PhD. 1997
- Leonard Liauwnardi, “Plastic Gear Transmission Error Measurements and Predictions”, MSc. 1997
- Ravikiran Kalluri, “Refinements in Root Stress Predictions at the Edges of Helical Gear Teeth”, MSc. 1997
- David Hochmann, “Friction Force Excitations in Spur and Helical Involute Parallel Axis Gearing”, PhD. 1997
- Brett Guhde, “Two Dimensional Gear Hobbing Simulation”, MSc. 1997
- Jon Wright, “An evaluation of the Gear Noise in an Automatic Transmission”, MSc. 1996
- Jun-Kyung Song, “Vibration Measurement on the Back-To-Back Stand by using Laser Vibrometer”, MSc. 1996
- Aaron M. Dziech, “Design of a Loaded Static Transmission Error Tester for Non-Parallel Axis Gearing”, MSc. 1996
- Victor Bolze, “Static and Dynamic Transmission Error Measurements and Predictions and Their Relation to Measured Noise for Several Gear Sets”, MSc. 1996
- Gordon Schroeder, “Torsional Vibration Isolation of a Flange Mounted Planetary Gearbox”, MSc. 1995
- Greg Matson, “A Synamic Study of a Back-toBack Gear Test Stand”, MSc. 1995
- Chun Li, “Automatic Design Method of Minimizing Gear Transmission Error with Torque Insensitivity”, MSc. 1995
- Jonny Harianto, “The Effect of Manufacturing Errors on Predicted Dynamic Factors of Spur Gears”, MSc. 1995
- Manish Prabhu, “Load Distribution and Transmission Error in Thin-Rimmed Gears Through Finite Element Analysis”, MSc. 1994
- James Graber, “A Theoretical and Experimental Study of Static and Dynamic Transmission Error for Spur and Helical Gears with Various Modifications and Contact Ratios”, MSc. 1994
- Sathya Vaidyanathan, “Application of Plate and Shell Models in the Loaded Tooth Contact Analysis of Bevel and Hypoid Gears”, PhD. 1993
- Sean O'Neal, “Prediction and Experimental Verification of Stresses at the Edges of Helical Gear Teeth”, MSc. 1993
- Mark. Clapper, “Gear Root Stress Prediction and Comparisons to Experimental and FEM Results”, MSc. 1993
- Craig Blazakis, “Effects of Thin-Rimmed Geometry on crack Propagation Path and Single Tooth Bending Fatigue Life of Spur Gears”, MSc. 1993
- Jeff Wheitner, “Investigation of the Effects of Manufacturing Variations and Materials on Fatigue Crack Detection Methods in Gear Teeth”, MSc. 1992
- Siva Sundaresan, “Design Optimization Procedure Using Robustness for Minimizing Transmission Error in Spur and Helical Gear”, PhD. 1992
- Avinash Singh, “Analysis of Spur and Helical Gears Using a Combination of Finite Element and Surface Integral Techniques”, MSc. 1992
- Anand Narayan, “Analysis of Worm Gears Using Finite Quasi Prismatic Elements”, MSc. 1992
- Vaidya Krishnan, “A Finite Element Procedure for Analyzing the Effects of Flexible Gear Blank Compliance on Load Distribution”, MSc. 1992
- David Hochmann, “An Improved Loaded Single Flank Static Transmission Error Tester”, MSc. 1992
- Harsh Vinayak, “An Experimental Study of Dynamic Transmission Error of Gear Pairs with Different Shaft Misalignments”, MSc. 1991
- Jacob Thomas, “A Procedure for Predicting the Load Distribution and Transmission Error Characteristics of Double Helical Gears”, MSc. 1991
- Atul Jhalani, “Development of a Three Dimensional Automatic Mesh Generation Program for Finite Quasi Prismatic Analysis of Spur and Helical Gears”, MSc. 1991
- Craig Foster, “Digital Control of a Loaded Single Flank Transmission Error Measuirement System”, MSc. 1991
- Frank Barhorst, “Detection of Fatigue Crack Initiation using Spur Gear Tooth Dynamic Stiffness changes during Load Controlled Single Tooth Fatigue Tests”, MSc. 1991
- Manish Vaishya, “Machine Simulation and Profile Generation in General Gear Manufacturing Processes”, MSc. 1990
- Sandeep Tilak, “Design, Analysis and Inspection of Spiral Bevel and Hypoid Gears using Tooth Contact Analysis Programs”, MSc. 1990
- V. Seetharaman, “Dynamic Analysis of Rotors Incorporating the Axial Coupling of Helical Gears”, MSc. 1990
- Eugene Liu, “Determination of Gear Root Stresses using Cantilever Plate Theory and Moment Image”, MSc. 1990
- M. Gopikrishnan, “Development of Finite Element Mesh Based on Manufacturing setup for Worm Gear Contact Analysis”, MSc. 1990
- Pete Biggert, “Comparisons between Measured and Predicted Tranmission Error of Unloaded Spur Gears”, MSc. 1990
- Sathya Vaidyanathan, “The Use of the SPBEVL program for the Design of Forging Dies for Spiral Bevel Gears”, MSc. 1989
- Siva Sundaresan, “The Development of a Knowledge Based Gear Design System which Incorporates Manufacturing Sensitivities which Affect Gear Noise”, MSc. 1989
- Chandra Sawh, “Design and Development of a Back to Back Gear Tester for dynamic Transmission Error Measurement”, MSc. 1989
- Luis Rojas, “Manual transmission gear rattle simulation and experimentation”, MSc. 1989
- Bernard Renggli, “Experimental and Finite Element Models for the Analysis of Die forces during Gear Extrusion”, MSc. 1989
- J.S. (Alex) Lin, “Experimental Analysis of Dynamic Force Transmissibility through Bearings”, MSc. 1989
- Jinmy Adjunta, “Design of Patterns and the Dimensional Evaluation of Gears Produced by the Investment and V-Sand Casting Processes”, MSc. 1989
- Win Young, “Force transmissibility modeling of bearings and housings”, MSc. 1988
- Timothy Craig Schutt, “Development of a Loaded Single Flank Transmission Error Measurement System using a Drive/Load Motor Configuration”, MSc. 1988
- Biplab Sarkar, “The use of a coordinate measurement machine for the measurement of gear tooth blanks and finish machined gears”, MSc. 1988
- Suresh Duraisamy, “Optimal Root Geometry and Fatigue Testing of Spur Gears”, MSc. 1988
- G. Wesley Blankenship, “Development and Testing of a Variable Center Distance Gear Noise Test Facility”, MSc. 1988
- Edward Yau, “Analysis of Shear Effect on Gear Tooth Deflections using the Rayleigh-Ritz Energy Method”, MSc. 1987
- Sandeep Vijayakar, “Finite Element Analysis of Quasi-Prismatic Bodies with Application to Gears”, PhD. 1987
- Robert Stakely, “Operating Parameters for a Loaded Rubber Belt CVT under both Driving and Test Stand Configurations”, MSc. 1987
- Chris O'Connor, “Techniques for Measuring Torsional Vibration and Gear Rattle”, MSc. 1987
- Jeff Eucker, “Measuring Gear Tooth Surfaces and Gear Tooth Deflections Using Holographic Interferometry”, MSc. 1987
- Mark Stegemiller, “The Effects of Base Flexibility on Thick Beams and Plates used in Gear Tooth Deflection Models”, MSc. 1986
- Timothy Magisos, “Measurement of Loaded Single Flank Transmission Error in Gesars using a Back-toBack Test Stand”, MSc. 1986
- Charles Denniston, “The Finite Element Analysis of Cogged V-belts in Two and Three Dimensions”, MSc. 1986
- Kirk Wirth, “Automotive Application of a Dual Hydraulically Actuated Rubber V-Belt CVT”, MSc. 1985
- David Lowe, “Experimental Determination of Spur Gear Tooth Deflection and Load Distribution and a Comparison with Predictions”, MSc. 1985
- Sam Linzell, “Performance Analysis of a Hydraulically Actuated Rubber V-Belt Continuously Variable Transmission”, MSc. 1985
- Duane Bassett, “Design of a Loaded, Gear Transmission Error Tester”, MSc. 1985
- David Yakubek, “Plate Bending and Finite Element Analysis of Spur and Helical Gear Tooth Deflections”, MSc. 1984
- Glen Steyer, “Spectral Estimations of Acoustic Intensity, Energy Density and Surface Velocity Using a Multi-Microphone Probe”, PhD. 1984
- Tony Previte, “Design, Development, and Testing of a Microcomputer Controlled, Dual Hydraulically Actuated, Rubber V-Belt, Continuously Variable Transmission”, MSc. 1984
- Douglas Pape, “Feasibility of Detecting Involute Crowning in Helical Gears by Signal Analysis”, MSc. 1984
- Gary Zaremsky, “Acoustic Intensity and Modal Analyses of a Gearbox Casing Plate”, MSc. 1983
- Massoud Tavakoli, “Optimization of Spur Gear Transmission Error using Profile Modifications”, MSc. 1983
- Richard Smigel, “A Comparison of Load Distribution Predictions with Measured Shaft Deflections and Gear Tooth Strains”, MSc. 1983
- Gholamreza Hosseini, “Three Dimensional Automatic Mesh Generation Program for Spur and Helical Gear Teeth”, MSc. 1983
- Robert Comparin, “The Dynamic Analysis of a Machine Tool Spindle”, MSc. 1983
- Mohammed Rajab, “Modeling of the Transmissibility through Rolling-Element Bearings Under Radial and Moment Loads”, PhD. 1982
- Duane Mattern, “Digital Control of a Continuously Variable Rubber V-Belt Transmission for an Automobile”, MSc. 1981
- Leonard Shaw, “Airframe Aerodynamic Noise - Total Radiated Acoustic Power Approach”, MSc. 1979
- Mark Lamontia, “Dynamic Modeling of Engine Block Components”, MSc. 1979
- P. Vohariwatt, “The Effects of Gear Fault and Coupling Misalignment on the Vibration Responses of a Geared System”, MSc. 1978
- Mordehy Cohen, “Measurement of Heat Generated in a V-Belt Drive”, MSc. 1978
- David Edmunds, “A Multi-Variable Control for a Variable Area Turbine Engine”, MSc. 1977
- Greg Takacs, “Dynamics of Printing Blankets”, MSc. 1976
- Al Gonsiska, “Nonlinear Analysis of V-Belt Vibration”, MSc. 1976
- Merlin Stingle, “Quality Control of Refrigeration Hermetic Compressors Using Signature Analysis”, MSc. 1975
- Mark Monsarrat, “Axial and Bending Fatigue of V-Belts”, MSc. 1974
- Michael Drosjack, “An Analytical and Experimental Study of the Effects of Tooth Surface Faults on a Geared System's Dynamic Response”, PhD. 1974
- Mitchell L. Yeary, “The Performance and Efficiency of the Asymmetric Variable Speed V-Belt Drive”, MSc. 1973
- Arthur Tinney, “The Analysis of Rolling Element Bearing Vibration Diagnostic Techniques”, MSc. 1973
- Ron Cook, “Multi-function Reactivity Insertion Device: Design and System Evaluation”, MSc. 1973
- Donald F. Sebian, “The Measurement and Display of Mechanical Speech Parameters”, MSc. 1972
- Daniel E. Kimmet, “The Motion of a V-Belt in a V-Groove in an Unloader Drive”, MSc. 1972
- Arthur A. Goldstein, “The Design and Development of a Closed Loop Hydraulic Dynamometer for a Rotating System”, MSc. 1972
- Douglas J. Niemeyer, “The Design of an Electro-Pneumatic Transducer for Use in Sensory Aid Applications”, MSc. 1971
- Ying Yen Kuo, “Investigation of Tube Transit Systems”, MSc. 1971
- Steve Goddard, “Gear Compliance and its Dynamic Effects”, MSc. 1971